SIG-Certified Armorer Chris Orndorff and our knowledgeable Members will do their best to answer your gunsmithing questions.
| | | Topic | Topic Starter | Replies | Views | Last Post |
|---|
 | | S&W 4516-1 | George43 | 0 | 562 |
|
| | P 220 Magazine | xfarfuldog | 11 | 1442 |
by hi-power man |
| | !! P226 Soft Hex Head Grips Screws !! SUCK !! | FLKev | 6 | 1075 |
by FLKev |
| | SRT Kit in German/W.German SIGs | Ian Douglas | 7 | 2575 |
by bczrx |
| | Sig Classic P229 Platinum Elite rear sight and dovetail. | jgerge222 | 0 | 545 |
|
| | Refinishing SIG rifles | cowbuyu | 6 | 1324 |
by KSGM |
| | S&W Model 60 not going into SA mode *FIXED* | Rolan_Kraps | 5 | 1282 |
by Rolan_Kraps |
| | .40 cal 229 with legacy slide question about conversion | Sulla123 | 6 | 1091 |
by SBrooks |
| | p229-22 Extractor Replacement | chengpu42 | 0 | 463 |
|
| | These Flat Triggers on the Legion and such. | cyberphobia | 6 | 1408 |
by Bulldog7972 |
| | SIG 220 SAO trigger bar springs | cyberphobia | 11 | 1000 |
by cyberphobia |
| | p229R-22 firing pin locating pin damage | chengpu42 | 1 | 701 |
by GaryBF |
| | Spare slide with red dot | NuJudge | 3 | 854 |
by hrcjon |
| | P226 .22 conversion kit issues | RedSoxMD | 3 | 759 |
by Nipper |
| | Mounting screws for Romeo 0 | Outdoorsman | 0 | 520 |
|
| | correct screw size for RMR mounting on P229 Pro-cut slide | rockspyder | 3 | 1136 |
by rockspyder |
| | SIG 220 SAO xray 3 sights | cyberphobia | 10 | 1161 |
by sigfreund |
| | Internal extractor Page 1 2 | Steve in PA | 20 | 6573 |
by cyberphobia |
| | Factory Sight Zero Question: Pistols and Optics | Conserve Liberty | 5 | 5064 |
by hrcjon |
| | Slide needs a lot of force to reinstall on MK25 after GG SRT Kit Install | RedSoxMD | 3 | 1071 |
by cyberiad |
| | P226 in 357 Sig/hollow-points FTF Page 1 2 | LFOD1776 | 20 | 3690 |
by Modern Day Savage |
| | Sig P229 magazine finish? | Racer_X | 0 | 654 |
|
| | CDL Refinishing ? Coating | Mr Bill @ SC | 1 | 716 |
by P220 Smudge |
| | P229 hard to rack with hammer down | les45 | 8 | 1964 |
by bob ramberg |
| | Excessive FCU to slide clearance? 320X5 Legion. | .45 STX Lover | 9 | 1914 |
by jason248 |
| | P320 trigger slap? | se3388 | 9 | 1981 |
by Jupiter |
| | Two thumbs up for this firearm refinisher…..unfortunately they are no longer offering refinishing services! | Rubec | 5 | 1264 |
by Rubec |
| | P365XL sights off center | Kilroy2721 | 3 | 2586 |
by stoic-one |
| | P320 40cal conversion | bschuu | 6 | 1112 |
by Nipper |
| | Sig 320 X5 one time two round burst | caryc | 2 | 746 |
by caryc |
| | Recommendation for THIN P220 wood grips | Rubec | 5 | 1481 |
by ckoz59 |
| | Dumb ass ammo/barrel issue | mike56 | 3 | 1034 |
by Nipper |
| | MK25 threaded barrel doesn’t fit | RedSoxMD | 2 | 781 |
by RedSoxMD |
| | Extractor issues M11A1 9mm | gas226 | 3 | 1202 |
by gas226 |
| | "Sig Arms" branded sight tool advice | lot_45 | 5 | 1219 |
by iron chef |
| | Upgrades and other stuff for older P229 | ripper20 | 4 | 1382 |
by ripper20 |
| | SIG P229C Carry 40S&W: PN for 357SIG Barrel? | XAVMECH | 4 | 936 |
by texassierra |
| | P229 Decocking when fired | TEXUN | 10 | 3438 |
by lot_45 |
| | Stamped slide P226 failure to extract | KevH | 5 | 1369 |
by cyberiad |
| | Sig p225 short trigger | Doc in Pa | 0 | 636 |
|
| | P220 Slide Catch Lever Question | hi-power man | 5 | 1217 |
by sigfreund |
| | P220 DAK field strip question ? | hi-power man | 6 | 1036 |
by Flash-LB |
| | What happens when you're STUPID! | pulicords | 19 | 4677 |
by se3388 |
| | Sight pusher for P320 | 10round | 1 | 702 |
by iron chef |
| | Firing pin positioning pin P220 | billinaz | 9 | 1880 |
by tonelar |
| | Will a P226 40 slide fit on a P226 9mm frame | sndbggr1484 | 6 | 2970 |
by mjohn |
| | Can’t remove slide on P226 .22 conversion kit | RedSoxMD | 3 | 1021 |
by bumper |
| | Problem with takedown lever on Sig P220 **UPDATE** | lilskeez | 5 | 1577 |
by lilskeez |
| | P226 sight removal w JMT pusher ? | hayseed | 3 | 1338 |
by TacoFrank |
| | P320 Custom FCU Build Issues | Wrek14 | 17 | 3324 |
by Lefty Sig |
