SIG-Certified Armorer Chris Orndorff and our knowledgeable Members will do their best to answer your gunsmithing questions.
| | | Topic | Topic Starter | Replies | Views | Last Post |
|---|
 | | Internal extractor Page 1 2 | Steve in PA | 20 | 7501 |
by cyberphobia |
| | Factory Sight Zero Question: Pistols and Optics | Conserve Liberty | 5 | 5861 |
by hrcjon |
| | Slide needs a lot of force to reinstall on MK25 after GG SRT Kit Install | RedSoxMD | 3 | 1237 |
by cyberiad |
| | P226 in 357 Sig/hollow-points FTF Page 1 2 | LFOD1776 | 20 | 4448 |
by Modern Day Savage |
| | Sig P229 magazine finish? | Racer_X | 0 | 770 |
|
| | CDL Refinishing ? Coating | Mr Bill @ SC | 1 | 909 |
by P220 Smudge |
| | P229 hard to rack with hammer down | les45 | 8 | 2455 |
by bob ramberg |
| | Excessive FCU to slide clearance? 320X5 Legion. | .45 STX Lover | 9 | 2247 |
by jason248 |
| | P320 trigger slap? | se3388 | 9 | 2449 |
by Jupiter |
| | Two thumbs up for this firearm refinisher…..unfortunately they are no longer offering refinishing services! | Rubec | 5 | 1541 |
by Rubec |
| | P365XL sights off center | Kilroy2721 | 3 | 2929 |
by stoic-one |
| | P320 40cal conversion | bschuu | 6 | 1432 |
by Nipper |
| | Sig 320 X5 one time two round burst | caryc | 2 | 957 |
by caryc |
| | Recommendation for THIN P220 wood grips | Rubec | 5 | 1790 |
by ckoz59 |
| | Dumb ass ammo/barrel issue | mike56 | 3 | 1298 |
by Nipper |
| | MK25 threaded barrel doesn’t fit | RedSoxMD | 2 | 990 |
by RedSoxMD |
| | Extractor issues M11A1 9mm | gas226 | 3 | 1493 |
by gas226 |
| | "Sig Arms" branded sight tool advice | lot_45 | 5 | 1523 |
by iron chef |
| | Upgrades and other stuff for older P229 | ripper20 | 4 | 1629 |
by ripper20 |
| | SIG P229C Carry 40S&W: PN for 357SIG Barrel? | XAVMECH | 4 | 1209 |
by texassierra |
| | P229 Decocking when fired | TEXUN | 10 | 4012 |
by lot_45 |
| | Stamped slide P226 failure to extract | KevH | 5 | 1731 |
by cyberiad |
| | Sig p225 short trigger | Doc in Pa | 0 | 787 |
|
| | P220 Slide Catch Lever Question | hi-power man | 5 | 1580 |
by sigfreund |
| | P220 DAK field strip question ? | hi-power man | 6 | 1354 |
by Flash-LB |
| | What happens when you're STUPID! | pulicords | 19 | 5218 |
by se3388 |
| | Sight pusher for P320 | 10round | 1 | 914 |
by iron chef |
| | Firing pin positioning pin P220 | billinaz | 9 | 2398 |
by tonelar |
| | Will a P226 40 slide fit on a P226 9mm frame | sndbggr1484 | 6 | 3744 |
by mjohn |
| | Can’t remove slide on P226 .22 conversion kit | RedSoxMD | 3 | 1256 |
by bumper |
| | Problem with takedown lever on Sig P220 **UPDATE** | lilskeez | 5 | 1932 |
by lilskeez |
| | P226 sight removal w JMT pusher ? | hayseed | 3 | 1602 |
by TacoFrank |
| | P320 Custom FCU Build Issues | Wrek14 | 17 | 4100 |
by Lefty Sig |
| | P320 red dot | gunnysgt | 2 | 4910 |
by Lefty Sig |
| | Which direction for rear sight removel | les45 | 5 | 1834 |
by bumper |
| | Gunsmith in NE Ohio | well1147 | 6 | 1908 |
by Blaque Jacque Shellaque |
| | 365 stuck after reassembly | Fuzzymcnab | 6 | 1481 |
by powermad |
| | Need optic/rear sight advice for 556 Classic Rifle | KyleDM5 | 0 | 629 |
|
| | Von Stavenhagen sight question | les45 | 5 | 1647 |
by les45 |
| | P938 Nose diving. | DeputyCG | 1 | 1292 |
by bumper |
| | My RMR finally came in and the screws are too big for my 92 LTT!!!! Help. Advice. | 357fuzz | 4 | 1436 |
by 357fuzz |
| | P220R with Romeo 3Max - co-witness options | Gordonwrogers | 3 | 1097 |
by PHC |
| | Any problems with LCI and tight Kydex holsters? | SoCal_CJD | 2 | 1054 |
by SoCal_CJD |
| | Frame Pin removal Page 1 2 | billinaz | 21 | 3979 |
by sigfreund |
| | Recoil Buffers | schrack | 3 | 1260 |
by mike28w |
| | Stronger P365 trigger spring? | 226blackwater | 1 | 1058 |
by Kilroy2721 |
| | P228 SIG parts not fitting question | JamesD | 14 | 3781 |
by bumper |
| | Bubba-ed Glock 21 barrel | RNshooter | 5 | 1547 |
by JWF |
| | Itahca 72 Saddle Gun | CycleT | 3 | 1281 |
by YooperSigs |
| | P220 triggers | billinaz | 3 | 1194 |
by sigfreund |
