SIGforum.com    Main Page  Hop To Forum Categories  SIG Pistols    Help with stuck slide on my P226
Go
New
Find
Notify
Tools
Reply
  
Help with stuck slide on my P226 Login/Join 
Member
posted
Guys Today at start of shift, I racked and loaded my duty 226 as always. End of shift I drop the mag and discovered the slide is jammed with a live round in the chamber. The slide is slightly pushed back, with the guide rod protruding out the front. HELP Not sure what to do with a live round in the weapon. Thanks as always Officer Dave
 
Posts: 305 | Location: Chicagoland  | Registered: September 15, 2007Reply With QuoteReport This Post
Member
posted Hide Post
Making sure to keep finger well away from trigger, I'd try to slam my left hand into the rear serrations with an overhand grip while punching forward with my right. This should jack the round out and in any case has everything moving more out of battery.

Just a really forceful round ejection.




“People have to really suffer before they can risk doing what they love.” –Chuck Palahnuik

Be harder to kill: https://preparefit.ck.page
 
Posts: 5043 | Location: Oregon | Registered: October 02, 2005Reply With QuoteReport This Post
His diet consists of black
coffee, and sarcasm.
Picture of egregore
posted Hide Post
quote:
Just a really forceful round ejection.

Agreed. There isn't much else you can do. With the slide most of the way in battery, the round can't be pushed out with a rod or punch, having nowhere to go. I had this happen to one of my guns when I unknowingly chambered a round that, when I finally got it out, turned out to have a bulged and crumpled case.
 
Posts: 28946 | Location: Johnson City, TN | Registered: April 28, 2012Reply With QuoteReport This Post
Member
posted Hide Post
My PPQ got stuck so bad I had to rap it with a padded punch and a mallet. Most of the time, you can push down against the end of a work bench or something. As you already noted, just be careful as you do have a live round in the chamber.


------------------------------------------------
Charter member of the vast, right-wing conspiracy
 
Posts: 1870 | Registered: June 25, 2010Reply With QuoteReport This Post
Freethinker
Picture of sigfreund
posted Hide Post
quote:
Originally posted by BuddyChryst:
Most of the time, you can push down against the end of a work bench or something.


That’s what I’ve done. Put the front of the slide on a sturdy wooden surface with the barrel hanging off and push down really vigorous and hard.




6.4/93.6
___________
“We are Americans …. Together we have resisted the trap of appeasement, cynicism, and isolation that gives temptation to tyrants.”
— George H. W. Bush
 
Posts: 47852 | Location: 10,150 Feet Above Sea Level in Colorado | Registered: April 04, 2002Reply With QuoteReport This Post
Member
posted Hide Post
Thanks guys! I slammed it hard and problem solved. Just cant figure out why it came out of battery in the first place. Thanks again, never to "old" to learn.
 
Posts: 305 | Location: Chicagoland  | Registered: September 15, 2007Reply With QuoteReport This Post
Lead slingin'
Parrot Head
Picture of Modern Day Savage
posted Hide Post
Glad to read that you were able to correct the stoppage.

My first guess would be a bad round but I'd be hesitant to rely on the gun for duty without making darn certain that it was reliable and that you had confirmed what caused the problem.

What did the chambered round look like after you were able to eject it?
 
Posts: 7324 | Location: the Centennial state | Registered: August 21, 2006Reply With QuoteReport This Post
Member
posted Hide Post
I had this happen twice. Turns out the second time a piece of debris was caught in the chamber. I have avoided problems recently by keeping my thumb firmly on the back of the slide while holstering. Some snug holsters will partially retract the slide as you insert the weapon. The slide can slide forward a bit when fully holstered, and a bit of something can get stuck. In my case, a bit of leather.
 
Posts: 17296 | Location: Lexington, KY | Registered: October 15, 2006Reply With QuoteReport This Post
Member
posted Hide Post
Check the barrel chamber for a piece of casing from a previously fired round. I have seen where a small ring of brass from the case separated and was bonded to the barrel chamber. The pistol will not go fully into battery on a slide release and will get jammed really tight, as you described.
 
Posts: 2034 | Location: Virginia | Registered: April 08, 2012Reply With QuoteReport This Post
Member
Picture of Chris Anchor
posted Hide Post
Make sure you test fire before putting back in to service. Not much good if it doesn't work. Chris
 
Posts: 1832 | Location: Cecil Co. Maryland | Registered: January 08, 2012Reply With QuoteReport This Post
Member
posted Hide Post
In my experience a stuck slide as described by the OP is usually the result of an out-of-spec round and happens during recoil or when the round is chambered after loading. I believe the pistol never went fully into battery when the slide was racked. I doubt that the slide was pushed out of battery by the holster and then managed to stick that tight.
 
Posts: 278 | Location: Utah | Registered: August 30, 2007Reply With QuoteReport This Post
Member
posted Hide Post
well it happened on a different frame. I have an alloy 226 frame and put the slide in question on it. Damn if the slide didn't jam after I loaded the last round. I load off my twenty round mag and then add a 21st round, topping off the mag. I saw an article that the mag may be to blame, not allowing the round to fully seat when loading. I switched out the 20 rounder( less than a year old) with a flush fit 18 rounder. So far so good. In addition, I went through the slide/frame etc looking for debris . I also dumped the duty ammo in the original 20 round mag and loaded brand new Federal HSTs. Need to get to the range to check function .
 
Posts: 305 | Location: Chicagoland  | Registered: September 15, 2007Reply With QuoteReport This Post
  Powered by Social Strata  
 

SIGforum.com    Main Page  Hop To Forum Categories  SIG Pistols    Help with stuck slide on my P226

© SIGforum 2024