SIGforum.com    Main Page  Hop To Forum Categories  The Essential Edge    Edge Retention Test- HAP40
Page 1 2 
Go
New
Find
Notify
Tools
Reply
  
Edge Retention Test- HAP40 Login/Join 
Triggers don't
pull themselves
Picture of mdblanton
posted Hide Post
quote:
Originally posted by offgrid:
quote:
Originally posted by mdblanton:
Thanks for the comments. I’ve given the reverse method (near polished edge and then a few passes with a rougher grit) a try but haven’t put enough time in it to perfect my technique yet.

Michael


I've read and watched most everything Clay Allison has put out. It tried this edge. https://www.youtube.com/watch?v=e4w0LqdMcGM

Border line between coarse stones/strop or two and the above edge. His micro bevel edge is a little easier to do.


I gave the Clay Allison method a try and will see how the edge holds up. 15 degrees (each side) for the profile through 1000 grit diamond followed by 4 passes at 200 grit diamond at 20 degrees each side. Definitely a toothy edge.


Michael
 
Posts: 1093 | Location: Petal, MS | Registered: January 21, 2012Reply With QuoteReport This Post
Member
posted Hide Post
mdblanton, how do you like that edge?

Picking up knives in Vandalis 4E and 20V today. See how those test!

djpaintles, going to try some Venev diamond stones next week. 150, 240, 400, 800. Will be interesting to see how they cut compared to the metallic bonded CBN stones.
 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
Triggers don't
pull themselves
Picture of mdblanton
posted Hide Post
It cuts well. It will slice paper and did a nice job cutting some running vines in the yard. I’m going to use it a bit more and then probably try touching up the micro bevel with 600 grit and see how I like that. Current stones I have for my Wicked Edge are 200/600 and 800/1000.

Michael
 
Posts: 1093 | Location: Petal, MS | Registered: January 21, 2012Reply With QuoteReport This Post
Member
posted Hide Post
quote:
Originally posted by offgrid:
mdblanton, how do you like that edge?

Picking up knives in Vandalis 4E and 20V today. See how those test!

djpaintles, going to try some Venev diamond stones next week. 150, 240, 400, 800. Will be interesting to see how they cut compared to the metallic bonded CBN stones.


I'm already looking forward to your comparisons. In my less detailed comparisons than you do it seemed to me that I got less extraneous scratches with the diamond stones and they were a little easier to flatten (no noxious chemicals needed). But I still need to do more knives with the CBN stones for a more accurate comparison. Both are a step above many other stones.

Gritomatic had a really good deal for a while on double sided Venev stones. It was 3 double sided stones for $80 or so. They fit just fine in the TSPROF if not in a regular edge pro. I also had bought a couple in regular edge pro blanks and they worked the same. The 2 sided ones just made for 1/2 as much angle setting going through the progression. :-)

You might check Venev Diamond stones Here:

https://www.gritomatic.com/pro...riant=14662079676525


Thanks again for your tests etc. They've cost me a lot of money on new stones I just "had" to buy LOL but I'm really glad you convinced me to look into them...............


Remember, this is all supposed to be for fun...................
 
Posts: 4123 | Registered: April 06, 2007Reply With QuoteReport This Post
Member
posted Hide Post
Benchmade 20V. 34 degrees, 300/700/1500CBN, 1 micron strop

14 minutes to sharpen, knife start/stop on the counter.

38 cuts/684"

I haven't sharpened this knife before. It definitely "felt" softer then what I remember from other knives in 20V. Stones cut very fast. The Benchmade specs I found on this knife state HRC 59-61. Maybe it's at the lower end of that HRC?

 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
Member
posted Hide Post
Spyderco PM2 M4. 34 degrees, Venev Diamond 240/400/800/1200, 1/.10 micron strop

19 minutes to sharpen

88 cuts/1584"

Used 2/3 stones from this Venev Beta Centauri set.

https://www.gritomatic.com/pro...riant=32302488092781

Since following previous angle, no need to go lower then the 240 grit. These stones load fast. Spent time cleaning them with a Nagura stone as using. Edge somewhat polished, some minor scratches left behind. I didn't chase a perfect mirror polish. While this polished edge cut more then the previous sharpening, I prefer a polished/toothy edge.

M4 is a great steel! Good edge retention, polishes very well.



PM2 I've slowly turned into a PM3!

 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
Member
posted Hide Post
 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
Member
posted Hide Post
Spyderco PM2 Maxamet. 34 degrees. 300/700/1500CBN, Spyderco Ultra Fine, 4/1/.5/.25/.1/.025 strops. Highly polished and sharp!

22 minutes to sharpen

190 cuts/3420"

Impressive edge retention! I have such a great appreciation for Spyderco and the steels they offer.

 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
Triggers don't
pull themselves
Picture of mdblanton
posted Hide Post
Off grid, thanks again for recommending the micro bevel sharpening method. I’ve been using the blade at work and have been very pleased with it. Cutting things like nylon strapping material has been very easy with no slip as I began the cuts. No slips during the cutting motion = a safer cut in my opinion. I’ve often had slips from more polished edges even though they were very sharp by the hair-shaving standard.

Michael
 
Posts: 1093 | Location: Petal, MS | Registered: January 21, 2012Reply With QuoteReport This Post
Member
posted Hide Post
Bradford G3 Wharnie Vanadis 4E. 30 degrees. 300/700CBN, 1/.25 micron strop.

14 minutes

62 cuts/1116"

Sharpens very similiar to M4. Not sure if it's the coating? Can see by the cardbaord not the cleanest cut, after the intial edge went through the cardboard would drag a little. Got a pretty good hot from the bottom of the finger choil. If it were my knife, would round down that point.

 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
Member
posted Hide Post
Up next, polished edge on a friends Creely Mako Rex 121!

Creely Mako's and Bradford G3. I much prefer the Mako in hand.

 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
Member
posted Hide Post
Creely Mako Rex 121. 30 degrees. 300/700/1500CBN, Spyderco UF, 4/1/.5/.25/.1/.025 strops. Give it a 8/10 for level of polish. Very sharp!

26 minutes to sharpen.

340 cuts/6120"

This steel blows me away! I believe if I continued to cut cardboard until it struggled, would go a long way. 340 is a lot of cuts! For a small knife it's very comfortable in my hand, no hot spots.

Fun stuff!

 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
always with a hat or sunscreen
Picture of bald1
posted Hide Post
Too bad you don't have a blade of Talonite. I'd be real curious how it would perform in your tests.

Back in 1999 I was one of the first to have knives made of this stuff (by Rob Simonich and Trace Rinaldi). Rob cut a lot of wood and rope testing the blade.


Will Fennell, then with Camillus, took a Talonite blade hog hunting and used it to butcher a couple without resharpening. So impressed that Camillus ended up collaborating with Rob on a design and with Tom Walz of Carbide Processors, producers of this metal.

Some early history: https://bladeforums.com/thread...t-is-talonite.84330/



Certifiable member of the gun toting, septuagenarian, bucket list workin', crazed retiree, bald is beautiful club!
USN (RET), COTEP #192
 
Posts: 16139 | Location: Black Hills of South Dakota | Registered: June 20, 2010Reply With QuoteReport This Post
Member
posted Hide Post
quote:
Originally posted by bald1:
Too bad you don't have a blade of Talonite. I'd be real curious how it would perform in your tests.

Back in 1999 I was one of the first to have knives made of this stuff (by Rob Simonich and Trace Rinaldi). Rob cut a lot of wood and rope testing the blade.

Will Fennell, then with Camillus, took a Talonite blade hog hunting and used it to butcher a couple without resharpening. So impressed that Camillus ended up collaborating with Rob on a design and with Tom Walz of Carbide Processors, producers of this metal.

Some early history: https://bladeforums.com/thread...t-is-talonite.84330/


Based on these tests, looks like Talonite would do poorly.

http://cliffstamp.com/knives/r...s/MEUK_talonite.html

http://cliffstamp.com/knives/r.../talonite_vg_10.html

http://cliffstamp.com/knives/reviews/talonite_D2.html
 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
always with a hat or sunscreen
Picture of bald1
posted Hide Post
quote:
Originally posted by offgrid:
quote:
Originally posted by bald1:
Too bad you don't have a blade of Talonite. I'd be real curious how it would perform in your tests.

Back in 1999 I was one of the first to have knives made of this stuff (by Rob Simonich and Trace Rinaldi). Rob cut a lot of wood and rope testing the blade.

Will Fennell, then with Camillus, took a Talonite blade hog hunting and used it to butcher a couple without resharpening. So impressed that Camillus ended up collaborating with Rob on a design and with Tom Walz of Carbide Processors, producers of this metal.

Some early history: https://bladeforums.com/thread...t-is-talonite.84330/


Based on these tests, looks like Talonite would do poorly.

http://cliffstamp.com/knives/r...s/MEUK_talonite.html

http://cliffstamp.com/knives/r.../talonite_vg_10.html

http://cliffstamp.com/knives/reviews/talonite_D2.html


Cliff Stamp was one with whom many many took issue. Frankly you shouldn't judge based on his reports period.



Certifiable member of the gun toting, septuagenarian, bucket list workin', crazed retiree, bald is beautiful club!
USN (RET), COTEP #192
 
Posts: 16139 | Location: Black Hills of South Dakota | Registered: June 20, 2010Reply With QuoteReport This Post
Member
posted Hide Post
quote:
Originally posted by bald1:
quote:
Originally posted by offgrid:
quote:
Originally posted by bald1:
Too bad you don't have a blade of Talonite. I'd be real curious how it would perform in your tests.

Back in 1999 I was one of the first to have knives made of this stuff (by Rob Simonich and Trace Rinaldi). Rob cut a lot of wood and rope testing the blade.

Will Fennell, then with Camillus, took a Talonite blade hog hunting and used it to butcher a couple without resharpening. So impressed that Camillus ended up collaborating with Rob on a design and with Tom Walz of Carbide Processors, producers of this metal.

Some early history: https://bladeforums.com/thread...t-is-talonite.84330/


Based on these tests, looks like Talonite would do poorly.

http://cliffstamp.com/knives/r...s/MEUK_talonite.html

http://cliffstamp.com/knives/r.../talonite_vg_10.html

http://cliffstamp.com/knives/reviews/talonite_D2.html


Cliff Stamp was one with whom many many took issue. Frankly you shouldn't judge based on his reports period.


http://www.zknives.com/knives/custom/triwhavk.shtml

Came across this test as well. 600" of cardboard before it would no longer cut free hanging paper. Not sure what kind of paper he used or a mininum sharpness level to start. I'm using rip cutting Rizla ciagrette paper as a mininum. Very few factory edges have passed this, high percentage of those have been quality kitchen knives. Based on his results guessing Talonite's edge retention would be similaiar to 154CM/ATS34, maybe 30V? If you're interested, glad to sharpen/test/sharpen it for you! See what we see.
 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
Member
posted Hide Post
GREAT Thread Offgrid! I hope you'll keep it up. I also hope I can find a Rex 121 Knife I like! :-D


Remember, this is all supposed to be for fun...................
 
Posts: 4123 | Registered: April 06, 2007Reply With QuoteReport This Post
Member
posted Hide Post
Spyderco PM2 30V. 34 degrees, Edge Pro 220, Shapton 500, Chosera 1000, 1 micron strop.

24 minutes to sharpen

11 cuts, 198"

The edge had a few little chips across the entire edge, I took out the chips in the area I was testing, left the chips toward the tip as I was going to resharpen after testing. Spent about half of the time on the EP 220 grit stone to get those chips out. How much material need to be removed to get those chips out, no doubt on fresh steel. Interesting test for sure! Shows us Diamond/CBN stones are the best choice to take advantage of this steel.

Resharpened it 300/700CBN/1 micron strop. 300 CBN blasted through the 30V, got rid of those chips toward the tip in short order. 14 minutes.

This message has been edited. Last edited by: offgrid,
 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
Member
posted Hide Post
Haven't done a test in quite awhile!

Spyderco Endura 4, HAP40 steel. 34 degrees, 300/700 CBN, 1 micron strop. Not sure of the hardness? Definitely felt a little on the hard side.

15 minutes to sharpen

70 cuts, 1260"

With this simple sharpening, edge had very good bite. Cut a tomato with the tip after the test, did well. Best I can measure the thickness behind the edge .022. This steel at .007-.010 BTE, under 30 degree angle, go up in grit... would be killer for a kitchen knife! Can see why this steel is used in Japanese kitchen knives.

My EDC PM2 Maxamet. Personally not a fan of the lock on the Endura, not a true one hand operation. Slightly bigger/wider PM2 feels a little better in my hand.

 
Posts: 3197 | Location: 9860 ft above sea level Colorado | Registered: December 31, 2008Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2  
 

SIGforum.com    Main Page  Hop To Forum Categories  The Essential Edge    Edge Retention Test- HAP40

© SIGforum 2024