SIGforum.com    Main Page  Hop To Forum Categories  The Lounge    Heat gun recommendation?
Page 1 2 
Go
New
Find
Notify
Tools
Reply
  
Heat gun recommendation? Login/Join 
Member
Picture of konata88
posted
I need a heat gun for heat shrink tubing (after solder splicing wires together - 22-10 gauge).

I was thinking the M18 cordless but the reviews aren't consistent - lack of heat for shrink tubing?

I was thinking cordless since I'm splicing outside sometimes. But corded isn't a deal breaker if there aren't any good cordless offerings.

Either way, any recommendations?

M18 compact heat gun good to go despite reviews? Other brand cordless? Corded recommendation?




"Wrong does not cease to be wrong because the majority share in it." L.Tolstoy
"A government is just a body of people, usually, notably, ungoverned." Shepherd Book
 
Posts: 13192 | Location: In the gilded cage | Registered: December 09, 2007Reply With QuoteReport This Post
Member
Picture of Tinyman
posted Hide Post
If you're very careful, a throwaway cigarete lighter has always worked for me.

Tinyman


______________________________

Stupid people are like glo-sticks.
I want to shake the shit out of them
till the light comes on
 
Posts: 315 | Location: Leeds, Alabama | Registered: August 28, 2019Reply With QuoteReport This Post
Ammoholic
Picture of Skins2881
posted Hide Post
I got my from Harbor Freight for like $15. It has lasted for years.



Jesse

Sic Semper Tyrannis
 
Posts: 21282 | Location: Loudoun County, Virginia | Registered: December 27, 2014Reply With QuoteReport This Post
No place to go and
all day to get there
Picture of JWF
posted Hide Post
quote:
Originally posted by Skins2881:
I got my from Harbor Freight for like $15. It has lasted for years.


This. I use one to start my BGE.


Just another day in paradise.

NRA
Georgia Carry
 
Posts: 1338 | Location: NW GA | Registered: September 08, 2012Reply With QuoteReport This Post
Member
Picture of ergoproxy
posted Hide Post
A $5 soldering iron will work as well. Use the sides of the tip, not the tip itself. I use this method when I use to race r/c cars as a hobby.
 
Posts: 1158 | Location: USA | Registered: December 28, 2006Reply With QuoteReport This Post
Member
Picture of maladat
posted Hide Post
I have a couple of super cheap plug-in ones that have been fine, and an M18 that I have only used a couple times but has been fine.

The one I actually use the most for heat shrink (it wouldn't work at all for a lot of other heat gun tasks) is this goofy little butane one that uses a lighter as a gas cartridge.

https://www.ancorproducts.com/en/702027

That's because I rarely need to shrink more than a couple pieces at a time, so the OK performance is compensated for by it being tiny and not needing to be plugged in or use a big heavy battery.
 
Posts: 6319 | Location: CA | Registered: January 24, 2011Reply With QuoteReport This Post
Member
Picture of PowerSurge
posted Hide Post
We use these at my company: https://www.amazon.com/DEWALT-...0%2Caps%2C183&sr=8-1

I have one of these at the house: https://www.amazon.com/DEWALT-...0%2Caps%2C183&sr=8-3

Both are great and get hot as hell!


———————————————
The fool hath said in his heart, There is no God. Psalm 14:1
 
Posts: 4039 | Location: Northeast Georgia | Registered: November 18, 2017Reply With QuoteReport This Post
Master-at-Arms
Picture of apf383
posted Hide Post
quote:
Originally posted by Skins2881:
I got my from Harbor Freight for like $15. It has lasted for years.


+1. Works for me!



Foster's, Australian for Bud

 
Posts: 7517 | Location: Stuck in NY, FUAC  | Registered: November 22, 2005Reply With QuoteReport This Post
Member
Picture of hairy2dawg
posted Hide Post
I've used soldering irons/guns, cigarette lighters, and mini torches to shrink with. My favorite is the cigarette type lighters that have a torch flame. They put out plenty of heat to get a good shrink, and works on windy days. I've never tried a heat gun, but seems like it might be a bit cumbersome. Soldering irons & guns work, but seems to be slower than a lighter.
 
Posts: 1289 | Location: Athens, GA | Registered: February 01, 2005Reply With QuoteReport This Post
Member
Picture of bigdeal
posted Hide Post
quote:
Originally posted by Skins2881:
I got my from Harbor Freight for like $15. It has lasted for years.
Yep.


-----------------------------
Guns are awesome because they shoot solid lead freedom. Every man should have several guns. And several dogs, because a man with a cat is a woman. Kurt Schlichter
 
Posts: 33845 | Location: Orlando, FL | Registered: April 30, 2006Reply With QuoteReport This Post
Member
Picture of aileron
posted Hide Post
I've had really good luck with a couple of these; primarily for heat shrink on avionics wiring. $25 and a lifetime warranty!


https://www.amazon.com/gp/prod...01_s00?ie=UTF8&psc=1
 
Posts: 1504 | Location: Montana - bear country | Registered: March 20, 2013Reply With QuoteReport This Post
Member
posted Hide Post
Heat gun is the way to go for great results.

Cordless due to its portability and ease of use without a cord becoming cumbersome.




 
Posts: 10062 | Registered: October 15, 2008Reply With QuoteReport This Post
Member
posted Hide Post
I have a Stanley corded heat gun, I've had it for 10 years and works great on on heat shrink tubing. I would think a heat gun uses too much energy for a cordless to last a long time between charges.
 
Posts: 21421 | Registered: June 12, 2005Reply With QuoteReport This Post
Member
posted Hide Post
Weller butane soldering iron, also works to heat shrink. https://www.amazon.com/Weller-...n/dp/B000WOHSHM?th=1
Harbor Freight has their brand for less money. Used a Weller for many years when doing field repairs before battery powered heat guns.
 
Posts: 1239 | Location: Moved to N.W. MT. | Registered: April 26, 2009Reply With QuoteReport This Post
His diet consists of black
coffee, and sarcasm.
Picture of egregore
posted Hide Post
My brother has a Milwaukee cordless heat gun and has said he doesn't like it, but I'm 99% sure it is also a M12, not an 18.

If you aren't working around flammable fumes like gasoline, the little butane torches work OK because you can direct the flame. Cigarette lighters suck because no matter how you hold them the flame can only go up. This can blow back on and burn you, if a breeze doesn't blow your flame out altogether. I use a corded heat gun from Snap-on (the "Blue-Point" brand), but I have them and other tool trucks come to my workplace. Interestingly - and surprisingly because so much stuff is made in China - it was made in Czech Republic.
 
Posts: 28974 | Location: Johnson City, TN | Registered: April 28, 2012Reply With QuoteReport This Post
Member
posted Hide Post
These work great on heat shrink tubing as well as heat shrink covering for model airplanes. Not too expensive either:

http://hobbyproinc.com/Top-Flite-Heat-Gun-TOPR2000/
 
Posts: 694 | Location: E. Central Missouri | Registered: January 05, 2011Reply With QuoteReport This Post
Member
Picture of Krazeehorse
posted Hide Post
quote:
Originally posted by Tinyman:
If you're very careful, a throwaway cigarete lighter has always worked for me.

Tinyman

Or upgrade to a cheap torch lighter. You can heat a different angles, not just from below. And you can use it in a breeze.


_____________________

Be careful what you tolerate. You are teaching people how to treat you.
 
Posts: 5747 | Location: Ohio | Registered: December 27, 2008Reply With QuoteReport This Post
Frog in boiling water
posted Hide Post
I use a small kitchen butane torch.
Just don’t get too close.


 
Posts: 436 | Location: Long Island,N. Y.  | Registered: November 08, 2009Reply With QuoteReport This Post
Member
Picture of maladat
posted Hide Post
quote:
Originally posted by egregore:
My brother has a Milwaukee cordless heat gun and has said he doesn't like it, but I'm 99% sure it is also a M12, not an 18.


Milwaukee makes an M12 soldering iron, but the heat gun is M18.
 
Posts: 6319 | Location: CA | Registered: January 24, 2011Reply With QuoteReport This Post
Member
Picture of konata88
posted Hide Post
Thanks guys. I’m going to avoid the M18 although it may fit my needs. I’m not an expert obviously but seems like heat shrink only needs a temp of about 70C, also sounds like 10-22g wiring insulation starts to melt around 90C (seems like a low bar to me though). These temps are at the low end of any heat gun.

But I’ll keep with branded corded. Makita and Dewalt have well rated models (kit with case). Probably lean toward one of those.




"Wrong does not cease to be wrong because the majority share in it." L.Tolstoy
"A government is just a body of people, usually, notably, ungoverned." Shepherd Book
 
Posts: 13192 | Location: In the gilded cage | Registered: December 09, 2007Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2  
 

SIGforum.com    Main Page  Hop To Forum Categories  The Lounge    Heat gun recommendation?

© SIGforum 2024