Main Page
The Lounge
Hardware/fastener experts what am I looking for and where do I find it?Go ![]() | New ![]() | Find ![]() | Notify ![]() | Tools ![]() | Reply ![]() | |
| Just because something is legal to do doesn't mean it is the smart thing to do. |
ontmark and I think alike. The picture showing the phone holder mounted on the dash looks a "obstructed vision" citation to me. I don't how many leos would write one but sometimes they look for anything if they are having a bad day. Integrity is doing the right thing, even when nobody is looking. | |||
|
| I have not yet begun to procrastinate |
I just used a suction cup windshield mount when I needed a setup like that. No way I’m digging around in my dash unless something is broken I can’t live without. I’d mess up something, it would rattle and drive me nuts. -------- After the game, the King and the pawn go into the same box. | |||
|
| Raised Hands Surround Us Three Nails To Protect Us |
Yes that phone holder is atrocious. Not doing that with mine. That was just the quickest google search pic I could show of the side of the mount. Not going to be mounting a phone like that. The tablet will be positioned directly above the stereo screen.
This is for an off-road setup not a suction cup mount would hold a tablet on an arm long enough for me to reach. This mount setup is very solid and won’t rattle. Taking apart the dash is not difficult just a little time consuming. I’ll be running wires too so taking it apart once is fine. Just don’t want to do it for each mount adjustment nor if I need to make adjustments on the trail do I want to take it apart. ———————————————— Dark nights I wrestle with my flaws in the silence. The enemy inside me turns my thoughts into violence but higher than despair is the rock that I climb. You’re the refuge in my chaos Lord, hear my cry!! | |||
|
| Member |
You can do the same thing with a simple stud and double nuts and tighten the 2 nuts together where you need the stops to be and it will act the same way. | |||
|
| Member |
Guess you missed the "male/female" part in the OP or "it is a sleeve that is internally threaded to accept a bolt". Got do more than read the thread title and look at a photo. | |||
|
| Raised Hands Surround Us Three Nails To Protect Us |
You are correct but it may be a good idea to take it a step further and read the entire thread before one goes calling folks out. In my update I added a possible option of using a bolt from the bottom with a clip washer. So he is correct a stud with a nut on both will work as he has suggested. Which I may end up doing and had though about my only issue is I don’t want the height of the nut under the top bracket. A clip washer with a flat washer over it should be low enough to not leave a noticeable gap. ———————————————— Dark nights I wrestle with my flaws in the silence. The enemy inside me turns my thoughts into violence but higher than despair is the rock that I climb. You’re the refuge in my chaos Lord, hear my cry!! | |||
|
| Cruising the Highway to Hell |
1st thought I had was carburetor mounting studs. https://www.holley.com/product...or_studs/parts/6346G “Government exists to protect us from each other. Where government has gone beyond its limits is in deciding to protect us from ourselves.” ― Ronald Reagan Retired old fart | |||
|
| Member |
Check into some of the really strong velcro. There is velcro that's self adhesive on both sides of it that is strong enough to hold that I believe. We use some incredibly strong velcro in the marine industry. | |||
|
| Just because something is legal to do doesn't mean it is the smart thing to do. |
Been a long time since I tore a engine head down but first thought was rocker arm studs. Integrity is doing the right thing, even when nobody is looking. | |||
|
| Member |
I guess you missed the BTW, I did read the whole thread, even your other thread on HVAC, where you say you don't have a heat pump, then later state you do... lol | |||
|
| Raised Hands Surround Us Three Nails To Protect Us |
So my mount finally came in and am getting the hardware together. Went to Fastenal and got some push nut bolt retainers. https://www.fastenal.com/products/details/0162890 Don’t think I’ll get a chance to install it this weekend though as the wife is working. And probably busy the weekend after Christmas. ———————————————— Dark nights I wrestle with my flaws in the silence. The enemy inside me turns my thoughts into violence but higher than despair is the rock that I climb. You’re the refuge in my chaos Lord, hear my cry!! | |||
|
| Powered by Social Strata | Page 1 2 |
| Please Wait. Your request is being processed... |
|
Main Page
The Lounge
Hardware/fastener experts what am I looking for and where do I find it?
