SIGforum.com    Main Page  Hop To Forum Categories  The Lounge    Suspension Grease Suggestions
Page 1 2 
Go
New
Find
Notify
Tools
Reply
  
Suspension Grease Suggestions Login/Join 
Oz_Shadow
Go Vols!
Picture of Oz_Shadow
posted Hide Post
quote:
Originally posted by Black92LX:
Yes the control arm bushings are poly and have zerk fittings.
And correct I am trying to stiffen the he suspension up a bit.

Just found this little nugget for poly bushing lubrication.

quote:
Bushing Lubrication
The suspension bushings included with this part can only be lubricated with PTFE grease, also referred to as "Marine Grease". PTFE grease is a very sticky, opaque grease that is water proof and will not degrade the bushing material. If lubed properly at installation, these bushings will not need to be lubricated again. Use of any other grease on these bushings will cause the bushing to fail and any bushing warranty to be voided.


Sounds like they prefer Mercury/Quicksilver 2-4-C
 
Posts: 17944 | Location: SE Michigan | Registered: February 10, 2007Reply With QuoteReport This Post
Plasteek
Member
posted Hide Post
Red Line CV-2
 
Posts: 109 | Location: Fort Wayne, IN. | Registered: February 25, 2019Reply With QuoteReport This Post
Black92LX
Raised Hands Surround Us
Three Nails To Protect Us
Picture of Black92LX
posted Hide Post
quote:
Originally posted by egregore:
quote:
Bushing Lubrication
The suspension bushings included with this part can only be lubricated with PTFE grease ...

OK, now we both know. Smile


And knowing is half the battle!

Super Lube seems to get some solid reviews with lots of mention on poly bushings.


————————————————
The world's not perfect, but it's not that bad.
If we got each other, and that's all we have.
I will be your brother, and I'll hold your hand.
You should know I'll be there for you!
 
Posts: 25956 | Registered: September 06, 2003Reply With QuoteReport This Post
MNSIG
Member
posted Hide Post
quote:
Originally posted by Flashlightboy:
M1 is good stuff for suspension bushings. Sticky and stays put.

My 229 likes it too.


I used to be a big fan of M1, but dang that stuff separates! I've got half a dozen grease guns of the same brand loaded with different products, and the only one that drips and leaks is the one with Mobil 1. It's always sitting in a puddle of red "oil" despite minimal temperature fluctuation in a heated/cooled garage. I assume it does the same thing where I can't see it.
 
Posts: 9136 | Location: The Red part of Minnesota | Registered: October 06, 2002Reply With QuoteReport This Post
shiftyvtec
Member
Picture of shiftyvtec
posted Hide Post
I'm surprised to see all the mobil 1 synthetic recommendations. Everybody seems to be a fan, but I've been disappointed in it for years due to its separation. Oozing all over the place after a reasonably short time in climate controlled shop???
 
Posts: 1585 | Location: Near Austin, TX | Registered: December 12, 2008Reply With QuoteReport This Post
henryaz
member
Picture of henryaz
posted Hide Post
quote:
Originally posted by Black92LX:
Super Lube seems to get some solid reviews with lots of mention on poly bushings.

I've been using Super Lube (NLGI 2) for my gun grease ever since Robert Burke sent along a sample tube when he returned a gun from some action work. It works very well, stays clear and hangs around a long time.


When in doubt, mumble
 
Posts: 10887 | Location: South Congress AZ | Registered: May 27, 2006Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2  
 

SIGforum.com    Main Page  Hop To Forum Categories  The Lounge    Suspension Grease Suggestions

© SIGforum 2024