SIGforum
The Importance of One Little Zero

This topic can be found at:
https://sigforum.com/eve/forums/a/tpc/f/230601935/m/1710047664

February 18, 2020, 01:44 PM
PHPaul
The Importance of One Little Zero
Needed a 5/8ths reamer for a job. That's...ummm....5 divided by 8, decimal point goes over here...0.625

Except that I ordered and received a 0.0625 reamer from McMaster.

The price should've been a hint...

After going back to McMaster and checking the price on the one I needed Eek vs. the one I ordered, I got a Chineseum one from Grizzly. Just need to bore and finish one aluminum pulley, should be okay, right?

Right?




Be careful when following the masses. Sometimes the M is silent.
February 18, 2020, 02:51 PM
TomS
Right

Wink


Best regards,

Tom


I have no comment at this time.
February 18, 2020, 08:24 PM
KP93
“Uhm yea sir,...Let me know how that works out for ya..” said my first Senior Chief to me almost three decades ago...MM SCPO Jerry Hudson was wise beyond his years for a “seasoned” A-Ganger serving in an elder lady of an LPH and training “his” then Division Officer — continued wishes to Sail Safe and Good Hunting Old Friend!

This message has been edited. Last edited by: KP93,


Navy BMD: When "Aim High" isn't High Enough!
February 18, 2020, 08:45 PM
Fredward
Try watching someone calculate a percentage discount. Hahahahah.
February 18, 2020, 08:54 PM
sigmonkey
Just ream the pulley under a really big magnifying glass...




"the meaning of life, is to give life meaning" Ani Yehudi אני יהודי Le'olam lo shuv לעולם לא שוב!
February 19, 2020, 09:05 AM
Perception
My brother repaired Caterpillars for a living for a long time, so quite a few of the tools he needed were plus size. After a few years of putting the snap on guy's kids through college, he came up with a new tool policy. When he needed something, he'd get it from Harbor Freight if he could. If he used it enough to break it, he would replace it with a quality version. It ended up being pretty rare that he had to pony up for the good stuff, and he ended up saving tens of thousands of dollars over the course of his career.

I have high hopes that your new reamer will make it through this first challenge!




"The people hate the lizards and the lizards rule the people."
"Odd," said Arthur, "I thought you said it was a democracy."
"I did," said Ford, "it is."
"So," said Arthur, hoping he wasn't sounding ridiculously obtuse, "why don't the people get rid of the lizards?"
"It honestly doesn't occur to them. They've all got the vote, so they all pretty much assume that the government they've voted in more or less approximates the government they want."
"You mean they actually vote for the lizards."
"Oh yes," said Ford with a shrug, "of course."
"But," said Arthur, going for the big one again, "why?"
"Because if they didn't vote for a lizard, then the wrong lizard might get in."
February 19, 2020, 01:16 PM
joel9507
quote:
Originally posted by PHPaul:
a 0.0625 reamer from McMaster.

Gotta admit, I'm surprised they make a reamer that size.
February 19, 2020, 06:25 PM
egregore
.0625 = 1/16. A sixteenth-inch reamer? Confused
February 19, 2020, 07:43 PM
PHPaul
quote:
Originally posted by egregore:
.0625 = 1/16. A sixteenth-inch reamer? Confused


Yup. Who knew? Can't imagine ever using it, but not worth returning.




Be careful when following the masses. Sometimes the M is silent.
February 19, 2020, 09:20 PM
tatortodd
quote:
Originally posted by PHPaul:
quote:
Originally posted by egregore:
.0625 = 1/16. A sixteenth-inch reamer? Confused


Yup. Who knew? Can't imagine ever using it, but not worth returning.
I'm envisioning a Dremel bit



Ego is the anesthesia that deadens the pain of stupidity

DISCLAIMER: These are the author's own personal views and do not represent the views of the author's employer.
February 20, 2020, 05:02 AM
PHPaul
quote:
Originally posted by tatortodd:
I'm envisioning a Dremel bit



Pretty much, yup.




Be careful when following the masses. Sometimes the M is silent.
February 20, 2020, 06:16 AM
Mars_Attacks
quote:
Originally posted by joel9507:
quote:
Originally posted by PHPaul:
a 0.0625 reamer from McMaster.

Gotta admit, I'm surprised they make a reamer that size.


They make them MUCH smaller than that for watchmaking.


____________________________

Eeewwww, don't touch it!
Here, poke at it with this stick.
February 20, 2020, 11:48 AM
Sig2340
quote:
Originally posted by PHPaul:
... Just need to bore and finish one aluminum pulley, should be okay, right?

Right?


You don't need a bigger reamer, you need a 1/32" line or cable.





Nice is overrated

"It's every freedom-loving individual's duty to lie to the government."
Airsoftguy, June 29, 2018
February 21, 2020, 06:45 PM
Scooter123
Hey Paul, you are into diorama's aren't you. Now you have the perfect reamer to make a 1/10 scale model of whatever that life size pulley goes on to.


I've stopped counting.
February 22, 2020, 05:41 AM
PHPaul
quote:
Originally posted by Scooter123:
Hey Paul, you are into diorama's aren't you. Now you have the perfect reamer to make a 1/10 scale model of whatever that life size pulley goes on to.


Big Grin

Just need to dream up something to use it for.




Be careful when following the masses. Sometimes the M is silent.
February 22, 2020, 07:51 AM
armedmd
quote:
Originally posted by PHPaul:
quote:
Originally posted by Scooter123:
Hey Paul, you are into diorama's aren't you. Now you have the perfect reamer to make a 1/10 scale model of whatever that life size pulley goes on to.


Big Grin

Just need to dream up something to use it for.


Having enjoyed many of your project posts here I’m confident you can and will do it and I look forward to the post about the project!


Build a man a fire and keep him warm for a night, set a man on fire and keep him warm the rest of his life.
February 22, 2020, 08:37 AM
Keystoner
In the machining world, the zero at the end is important too: 0.625 ≠ 0.6250



Year V
February 22, 2020, 09:22 AM
PHPaul
quote:
Originally posted by Keystoner:
In the machining world, the zero at the end is important too: 0.625 ≠ 0.6250






You mean like this?

I'm waiting on the reamer to arrive to finish the bore and then I can broach the keyway to match.




Be careful when following the masses. Sometimes the M is silent.
February 23, 2020, 07:56 AM
Kskelton
It’s just a zero. Zero = nothing you’ll be fine :-D


www.OneStopFirearms.com
March 02, 2020, 06:38 AM
Scooter123
quote:
Originally posted by Kskelton:
It’s just a zero. Zero = nothing you’ll be fine :-D


In my world that 4th decimal signifies a tolerance of +/- 0.0005 inch (unless otherwise specified). So it aint "nothin".


I've stopped counting.