SIGforum.com    Main Page  Hop To Forum Categories  Suppressed Weapons    OAL for AR and MPX for Form 1?
Go
New
Find
Notify
Tools
Reply
  
OAL for AR and MPX for Form 1? Login/Join 
Web Clavin Extraordinaire
Picture of Oat_Action_Man
posted
I'm in the process of filling out my first Form 1s to make two SBRs.

Can anyone help me with the OALs of the two guns?

One is an LMT CQB which will have an 11.5" barrel.

The other is an MPX pistol with an 8" barrel.

Any other Form 1 mishaps to avoid? I'm filing as an individual.


----------------------------

Chuck Norris put the laughter in "manslaughter"

Educating the youth of America, one declension at a time.
 
Posts: 17808 | Location: SE PA | Registered: January 12, 2001Reply With QuoteReport This Post
Member
posted Hide Post
well it depends what stock you plan on putting on them.

IIRC.. the OAL is with the stock fully extended


_________________________________________________________

This is where my signature goes.
 
Posts: 805 | Location: Cary, NC | Registered: June 04, 2015Reply With QuoteReport This Post
Oriental Redneck
Picture of 12131
posted Hide Post
quote:
Originally posted by creslin:
IIRC.. the OAL is with the stock fully extended

Correct.
 
Posts: 15669 | Location: TEXAS | Registered: September 04, 2008Reply With QuoteReport This Post
I run trains!
Picture of SigM4
posted Hide Post
As info my 11.5” BCM with a CTR is 31.25” overall. Would assume you’d be somewhere close to that.



Success always occurs in private, and failure in full view.
 
Posts: 4134 | Location: Willow Park, TX | Registered: April 14, 2006Reply With QuoteReport This Post
Web Clavin Extraordinaire
Picture of Oat_Action_Man
posted Hide Post
Well I guess I can just measure the current length of the LMT and subtract 4.5", but that still leaves the MPX.


----------------------------

Chuck Norris put the laughter in "manslaughter"

Educating the youth of America, one declension at a time.
 
Posts: 17808 | Location: SE PA | Registered: January 12, 2001Reply With QuoteReport This Post
Member
posted Hide Post
Measure the MPX muzzle to rear pic rail and then get a measurement for the stock you want. I had decent luck with my MP5K SBR by just Googling it. I found a few sources that agreed and went with that.
 
Posts: 2228 | Location: Iowa | Registered: February 24, 2011Reply With QuoteReport This Post
Web Clavin Extraordinaire
Picture of Oat_Action_Man
posted Hide Post
So I actually found some numbers for an MPX in an early review and both the side folder and the collapsible stocks on an 8" barrel seem to bring it in below 26" when fully extended.

The side folder seems to be 25.75" and the collapsible stock is 25.25".


----------------------------

Chuck Norris put the laughter in "manslaughter"

Educating the youth of America, one declension at a time.
 
Posts: 17808 | Location: SE PA | Registered: January 12, 2001Reply With QuoteReport This Post
Member
Picture of nhracecraft
posted Hide Post
quote:
Originally posted by Oat_Action_Man:
Well I guess I can just measure the current length of the LMT and subtract 4.5", but that still leaves the MPX.

For reference, I have an LMT CQBPS12 (Factory SBR w/ 12" Barrel) and my Form 4 indicates an OAL of 32.25"


____________________________________________________________

If Some is Good, and More is Better.....then Too Much, is Just Enough !!
 
Posts: 3044 | Location: New Hampshire | Registered: October 29, 2011Reply With QuoteReport This Post
  Powered by Social Strata  
 

SIGforum.com    Main Page  Hop To Forum Categories  Suppressed Weapons    OAL for AR and MPX for Form 1?

© SIGforum 2018