SIGforum.com    Main Page  Hop To Forum Categories  The Mason-Howe Rifle Room    Ruger Gen 2 American Ranch Rifle going back for service
Go
New
Find
Notify
Tools
Reply
  
Ruger Gen 2 American Ranch Rifle going back for service Login/Join 
Jack of All Trades,
Master of Nothing
Picture of 2000Z-71
posted
So was all excited to get my Ranch Rifle and set it up for a suppressor. Really kind of a unique rifle, lightweight, short barrel, takes AR magazines, threaded barrel and chambered in .300 Blackout. Plans are to set it up with an LPVO and a supressor.

Mounted a cheapie red dot that I had sitting around on the rail to take it out to function check it. While the bolt was a little rough in operation cycling it without a round in the chamber I consoled myself that it was a $550 rifle and not a $1,500 rifle. The problem I have now with chambering a round is that it takes an inordinate amount of pressure to close the bolt. I can’t do it from a shooting position from the bench. I literally have to stand up and apply body weight through my arm to close the bolt to chamber a live round. This was the case with both the Hornady 210gr and Winchester 140gr factory loads.

I did not even try and fire it in this condition. Concerned there is a head spacing issue with the rifle and did not want a KABOOM! to prove it. So e-mail into Ruger explaining the problem and requesting a return.

Frustrating. I really like the rifle and the idea behind it. Why is it quality control with firearm manufacturers just seems to be non-existent? I would think every rifle would be checked for head spacing before it left the factory.




My daughter can deflate your daughter's soccer ball.
 
Posts: 12401 | Location: Eagle River, AK | Registered: September 12, 2006Reply With QuoteReport This Post
Member
Picture of sourdough44
posted Hide Post
Yeah, if it’s that hard to close the bolt with factory ammo, 2 types, something is amiss.

This assumes all is clean, I doubt any base screws would affect anything. If you did anything to the gun that has a chance of interference, undo it.

Again, just skimming, doesn’t seem the case.
 
Posts: 7646 | Location: WI | Registered: February 29, 2012Reply With QuoteReport This Post
Like a party
in your pants
Picture of armored
posted Hide Post
Do I remember correctly that you had a big problem with 3 Ruger Mountain handguns a while back that you purchased new?
 
Posts: 5419 | Location: Chicago, IL, USA: | Registered: November 17, 2002Reply With QuoteReport This Post
Member
Picture of sourdough44
posted Hide Post
Another thing, assuming you still have the rifle, you could troubleshoot. I would assume it closes fine with an empty chamber? Maybe use a marker on the cartridge, try to see what area is hanging up?

Could be bullet, neck, shoulder, case near the base.

Another thing is if the extractor is stuck or hanging up. There are ways to test & fiddle with it.

Maybe try another type of ammo or 2. Not trying to let Ruger off the hook, I’d just want to know a little.

Over the years I bought two USED rifles with chamber problems. The 1st was oversized, failed to fire factory ammo half the time. It was evaluated by Browning. They blamed a history of strong reloads.

The 2nd was a Savage 110 30-06, wouldn’t chamber a factory round. Once the old wood stock was removed, it chambered fine. When the stock was screwed in, it twisted the action enough to not chamber a round. I wouldn’t have believed it, but now 100% ok with a replacement stock.

If you’re in the mood to fiddle.
 
Posts: 7646 | Location: WI | Registered: February 29, 2012Reply With QuoteReport This Post
  Powered by Social Strata  
 

SIGforum.com    Main Page  Hop To Forum Categories  The Mason-Howe Rifle Room    Ruger Gen 2 American Ranch Rifle going back for service

© SIGforum 2026