Main Page
The Mason-Howe Rifle Room
Assembling a bolt gun for the first time. Question regarding scope rings REVISED: Rings vs One Piece Mount.Go ![]() | New ![]() | Find ![]() | Notify ![]() | Tools ![]() | Reply ![]() | |
| Ice age heat wave, cant complain. ![]() |
This may be an ongoing series of questions, but today it pertains to scope rings. My dealer has a Tikka CTR in 6.5CM inbound. This is my first bolt gun so I don't know shit about shit. I intend to put a NF NX6 5-30 on it. I'm not familiar with scope rings but I'm looking at Area419. How does one determine the ring height? On AR/LPVO's I know I'm a 1.70 guy. Also, would the ring height be affected by an aftermarket chassis like a KRG Bravo?This message has been edited. Last edited by: MikeGLI, NRA Life Member Steak: Rare. Coffee: Black. Bourbon: Neat. | ||
|
| Freethinker |
Although I have no experience with them, I assume that area 419 rings are good just based on the company’s overall reputation. There’s less to be bad about scope rings than about most firearms accessories, but I suspect the reason to avoid the cheapest types is that if they’re not machined properly they can exert uneven force on the scope. That’s why it was a practice at one time to lap the rings to remove any unevenness. That doesn’t seem to be common these days, though. I have an ancient lapping rod for 1 inch rings, but I’m not even aware of lapping rods for larger rings, although they may exist. Most of my scope mounts are either Leupold or Spuhr, and mainly just because, not that I believe they’re inherently superior to other brands. Keep in mind that there are many different scope main tube sizes these days, and we must have the proper size rings. According to the ’net your scope has a 34mm main tube, which is probably the most common size for scopes of that type. (For some reason the Leupold Mark 5HD models have 35mm tubes, so the 34mm rings in my spares box don’t work with them. Ring height is a somewhat complex subject. Many people believe that the height should be low enough to permit a firm stock/cheek weld, and especially to avoid the dreaded “chin weld” that doesn’t have firm contact and pressure between cheek and stock. As I’ve discussed in another recent post, I used to be a believer in that idea, but I’ve gotten away from it in recent times, and find that light cheek-to-stock pressure is better for me to avoid vertical stringing and other problems. But not everyone believes that, so it’s something you need to decide for yourself. One thing that is essential is that the rings are high enough to permit the scope to be mounted properly without the objective bell touching the rifle barrel. For example, I have a Leupold Mark 5HD 5-25×56mm scope mounted on my Tikka 6.5 CTR, and with Leupold high Mark 4 rings the objective bell with lens cap and a Camo Form wrap clears the barrel slightly, but not by a huge amount. When looking at ring height specifications, according to the Gemini AI the most common method that ring manufacturers use these days for designating height is from the base that contacts something like the top of a Picatinny mounting rail to the centerline of the scope. But there are evidently exceptions for less common brands. The high Leopold rings I have are specified as being 1.06 inch high, and because there’s a little gap between the ring and the Pic rail, my measurement is 1.1 inch from top of the rail to scope center. On the other hand, on my 308 Winchester CTR I have a Leupold Mark 5HD 2-10×30mm scope, and because its objective lens is so much smaller, I have it mounted with Leupold Mark 4 “medium” rings, that are nominally 0.90" high. (I should probably change that and another CTR scope to high for consistent cheek position, but ….) Stocks do affect how high a scope needs to be mounted as well. If the stock raises the cheek up too high for a preferred cheek weld, then higher rings are necessary. Traditional hunting rifle stock combs (the highest part where the cheek rests) were offset down below the line of the receiver, and that was at least in part to permit using “iron” sights that were mounted low on the receiver and barrel. To this day traditional hunting rifles with factory iron sights have a stock comb that’s offset lower than the receiver and barrel. Because iron sights are much less common these days, and because rifles like the Tikka CTR models don’t have them, the trend is to raise the stock comb for better alignment with a scope sight. That’s the purpose of the add-on riser on the CTR stock (for some reason, in this country that riser is fixed rather than adjustable in height as is possible with models sold in Europe). That’s also why chassis like the KRG Bravo have an adjustable cheek riser. I have a KRG Whisky (3?) chassis, and with the cheek riser in the full-down position, its top is about as high as the riser on my 6.5 CTR stock, but only “about” because I can’t measure it exactly. The advantage of an adjustable riser is of course that it can be raised for use with a higher scope mount if desired. Anyway, a long discussion, but I hope it’s of some use. “Most men … can seldom accept the simplest and most obvious truth if it … would oblige them to admit the falsity of conclusions … which they have woven, thread by thread, into the fabrics of their lives.” — Leo Tolstoy | |||
|
| Ice age heat wave, cant complain. ![]() |
Well, when I saw you replied to my post, I was hoping you just said "28MM". I appreciated your detailed response. This is going to be a lot of learning on my end so your input is valued. NRA Life Member Steak: Rare. Coffee: Black. Bourbon: Neat. | |||
|
| Ice age heat wave, cant complain. ![]() |
Just started the youtube search, this was short and sweet. Echoing some of what sigfreund outlined. NRA Life Member Steak: Rare. Coffee: Black. Bourbon: Neat. | |||
|
| Member |
That shows the difference between people who just own guns and those who actual shoot them. If your rifle's buttstock doesn't have an adjustable cheek rest, then it's a bit of a crapshoot. I like a higher mount, where I don't need to press my cheek hard onto the stock to obtain the proper eyebox picture. I have Nightforce rings on my precision bolt actions. I prefer their 1.375" extra high, but can work with 1.125" if the stock is right. I also have 20MOA canted rails, which slightly increases effective scope height. You're probably looking at 419's 28mm or 32mm rings. Consider if you like a hard or soft cheek weld. I recommend looking at Nightforce rings, too. Call Sportoptics.com, get a live agent, and you'll likely get 10% (more or less) off the list price. Regardless of which vendor you go with, mention that you're new to this hold bolt action thingie. You're concerned that you might not order the best ring height. Ask if the vendor allows simple & free/minimal exchange for a different height set. | |||
|
Spread the Disease![]() |
There are several handy ring height calculators out there. Here's one . ________________________________________ -- Fear is the mind-killer. Fear is the little-death that brings total obliteration. I will face my fear. I will permit it to pass over me and through me. And when it has gone past me I will turn the inner eye to see its path. Where the fear has gone there will be nothing. Only I will remain. -- | |||
|
| Ice age heat wave, cant complain. ![]() |
Well, not only is this my first bolt gun, I've never so much as SHOT one, so I really don't know. But I have greater than average time on an AR pattern rifle, and I don't mind a hard cheek weld. I cant say if the two translate but I can tell you I don't like the feeling of not being able to get down low enough for the optic. Noted on the NF rings, I'll check them out. NRA Life Member Steak: Rare. Coffee: Black. Bourbon: Neat. | |||
|
| Ice age heat wave, cant complain. ![]() |
So my research now has me looking at 1 piece mounts as an alternative to rings. Other than weight, what are the pros/cons of a 1 piece mount. I'm also seeing a lot of mounts offering 20MOA options or OMOA options. What's this about? NRA Life Member Steak: Rare. Coffee: Black. Bourbon: Neat. | |||
|
| Freethinker |
The claimed advantage of a one-piece mount is that they’re more rigid, and, probably if they’re a good brand, that there cannot be any misalignment between the rings. I like Spuhr one-piece mounts, but not because I believe that there is anything wrong with separate good quality rings. That, however, is just my personal opinion. Many precision competitors evidently do like one-piece mounts. A mount that’s labeled something like 20 MOA means that the back is canted up with respect to the front to add 20 minutes of angle of elevation to whatever your scope is adjusted to. The primary reason to have such a mount is to help keep from running out of elevation adjustment for long range shooting. The possible disadvantage of too much additional elevation in the base is that it could prevent dialing down far enough for some applications, such as at closer ranges. For example, if one’s scope had only ± 30 MOA of elevation and the base was +60 MOA, then that could be a problem for shooting at normal distances because you’d still be 30 MOA high when dialed all the way down. That example is an exaggeration of anything likely in reality, but hopefully explains what I’m referring to. My general practice for one-piece mounts is to get Spuhr mounts that add 6 milliradians (+ 20.6 MOA) of elevation because I believe it can’t hurt*, and could be useful for shooting at long ranges if I ever wanted to do that—especially with rifles chambered for 22 Long Rifle. * Added: I say that, but with certain scopes that have a limited elevation adjustment range, a possible disadvantage of a +MOA base is that even if we don’t completely run out of down elevation, scopes usually do better optically and mechanically if the elevation or windage adjustment isn’t near the end of its range. If an elevation adjustment is very close to the maximum up or down, that can even interfere with how much windage adjustment is possible due to the mechanical design of the scope. Somewhat paradoxically, an increased elevation base is less likely to cause problems for a scope that already has a large adjustment range internally. This is no sort of recommendation, but the elevation range of the scope you mentioned is 120 MOA, or ±60 MOA. If the scope were mine, I would not hesitate to use a +20 MOA base with it unless I were convinced I’d never want to shoot it at long ranges, but of course it’s not mine. By way of comparison, I have two scopes mounted on 22LR rifles that have only 100 MOA (±50 MOA) of elevation, and their +20.6 MOA bases have caused me no problems. FWIW, the scope on my T3x 6.5 CM CTR is mounted in separate Leupold 0 MOA rings, but I have other rifles I’d use if I ever wanted to engage really long range targets. “Most men … can seldom accept the simplest and most obvious truth if it … would oblige them to admit the falsity of conclusions … which they have woven, thread by thread, into the fabrics of their lives.” — Leo Tolstoy | |||
|
| Member |
For a precision rifle, the weight difference is insignificant. One piece mounts are stiffer, but for a well-built bolt action rifle with a solid receiver top (i.e. a cut out only on the bolt ejection side of the receiver), the stiffness difference is insignificant. One piece mounts are almost always more expensive than rings. If you go this route, make certain the mount is optimized for a bolt action rifle, not an AR. I believe your rail is flat, with no cant. This means the rail is parallel with the bore. Sighting at 100 yards will require elevation increase of maybe 2-4 MOA, which leaves you a theoretical 56-58 MOA to use for longer distance targets with the scope you list. Ballpark estimates for air density equivalent of 4,000 feet, you'll dial up the following elevations on your turrets: -- 10 MOA for 530 yards -- 20 MOA for 830 yards -- 30 MOA for 1065 yards All well below the scope's maximum. And probably well within your expected shooting. So...you don't need a canted rail of 20 MOA, but it won't hurt, either. That said, almost every precision rifle and AR I own has a rail cant of 20 MOA. I've shot targets out to the practical flight limits of almost every rifle/AR I've owned, and thus a 20 MOA cant makes sense for my use. A canted rail also offers slightly better optical quality at longer distances, IMO most noticeably around the edges of the viewing field. In theory, the canted rail rail offers more windage dialing capacity at extended ranges. In practice, this has the probability of this year's Sports Illustrated swimsuit cover model showing up at my front door and wanting to be my sex slave. The NF reticles for my long distance precision rifles are calibrated for 20 MOA of windage. I almost never dial windage, but prefer to hold via reticle. The only times I've dialed windage in matches: - Maybe 10-15 MOA for special F-U stages where the target is hidden over a ridge, and the shooter must dial windage from an aiming pole in order to hit the target. Such targets were generally in the 400-500 yard ballpark. - Maybe 7-12 MOA for laterally moving targets with extreme side winds. Targets were in the 500-900 yard ballpark. - 10 or 15 MOA on ELR stages in Wyoming, where the matches were held right next to wind farms. Wind holds on the true ELR targets -- those over 1400 yards -- were greater than the 20 MOA on my reticles. I generally dialed 10 MOA in these situations, as mental windage calculations for all distances (say 800-1800 yards) was the easiest. The longest targets (1500-1800 yards) in the highest winds resulted in using almost all of the reticle windage, even with 10 or 15 MOA dialed in. Very, very few shooters will ever experience such conditions in their life. In the steel matches I've attended, the competitors using rings versus one-piece mounts is likely in the ballpark 10-to-1 ratio. I don't expect your having issues with no cant and rings with this rifle & scope. But you won't have issues with a one-piece canted mount, either. | |||
|
| Member |
A couple observations on your rifle and scope. That's a beast of a scope for a 6.5 Creed but since the CTR is a heavier barreled option it might not unbalance the rifle too much. I prefer lighter scopes on lighter rifles. Tikka's are a little odd in that they have a dovetail rail that runs along the top of the receiver. If you are going lightweight Talley makes ring mounts that slide onto the rail and screw in from the top. I think for what you are wanting to do you would be much better off buying a Picatinny Rail to cover up the dovetail on the receiver and then you can use any MIL-1913 STD "Picatinny" rings on your rail. My personal preference is to mount scopes as low to the bore as possible. I'm thick chested and short necked. If you have long arms a long neck you might very well fit best with the exact opposite! If there's any way possible I strongly suggest you go to a well stocked gunstore that sells rings. A lot of them will let you try the rings and bases on your rifle to see if they fit for you before you buy them. You can save a LOT by trying before you buy but then again you might not live a mile from a Scheels store like I do. I would "Guess" that if you are used to shooting AR's quite a bit you might be happier with a little higher ring setup than a prone shooter etc might like. Again if there's anyway to test in a store I highly recommend you try before you buy. The CTR cheekrest is adjustable so if you can't I "think" you should try the slightly higher of two given choices. And YES Chassis CAN affect your ring Height. I have a couple AI Chassis that make it impossible to mount the scope super low but with the adjustable cheekpiece you can get a good Cheek weld comfortably. Ideally you want your scope, Stock and rings to fit you like a shotgun almost. Take your unloaded rifle, close your eyes, shoulder it and aim at a target in front of you. With a perfectly fitted rifle you will be looking right down the center of the scope and on target when using your natural point of aim. (another interesting subject). Adjustable stocks help you fidget around to close as possible. Now days you almost never see a fitted wooden stock but they are SWEET when you have one! IMHO SPUHR mounts are one of the best you can buy, they are just expensive as heck buy them if you can afford them. There are plenty of other good ones around though, Seekins Rings are excellent and less expensive than SPUHR and some of the others. Even some of the inexpensive Chinese mounts are superior to good mounts 30-40 years ago. Which brings up a Controversial opinion of mine that others are free to disagree with but I learned this the hard way. Modern mounts like Spuhr, Talley, Seekins etc etc are made on super accurate CNC machines that mill then round to thousandths or better. If you LAP THESE RINGS any metal you remove is going to make them LESS ROUND! I STRONGLY recommend that you DO NOT LAP modern rings! I lapped a set of modern rings and it made them out of round enough that they pinched the scope tube enough the magnification ring wouldn't turn! Lapping them RUINED those rings. Some old rifle receivers were milled and drilled crooked as hell sometimes and you had to shim, lap and do all sorts of nonsense to get your scope on straight. You won't have this problem with a Tikka T3x so DON"T LAP any rings you put on it! Get a good base, good rings and torque them to what the ring spec tell you to, You won't have any issues. Another couple little things: YODAVE makes a spring for $10 or so that will help you safely lower your trigger pull by a Pound or so. I've used them in several of my Tikka's and Sako's. If you Reload most Tikka's and Sako's have long throats so you might be able to seat your bullets out longer than normal Saami Spec. We can talk reloading on another thread if you'd like. Anyway Best of Luck with your new rifle! I have a Tikka T3x Tactical in 6.5 Creed that was an absolute DRILL of a rifle. I bet yours is going to shoot GREAT Too!...................dj Remember, this is all supposed to be for fun................... | |||
|
| Member |
Another quick thing. If you are using a Picatinny rail and rings you will be glad if you buy one of these Scope level kits; https://www.amazon.com/DISCOVE...g%2Caps%2C297&sr=8-9 If you buy a SPUHR mount you'll get a better on of these in the box. The Discovery Opt is an inexpensive copy of the SPUHR version. Just remember to pull out the triangle before you fully tighten the screws or you won't get it out! :-) Remember, this is all supposed to be for fun................... | |||
|
| Freethinker |
You are getting great advice from two very knowledgeable and experienced shooters. A couple of clarifications: The current Tikka CTR models such as the three I own don’t have adjustable cheek pieces. The ones sold in Europe do, and why we can’t have those is a mystery, but …. Perhaps that will change as I saw one rifle on the EuroOptic site that had a non-chassis traditional stock and the adjustable cheek piece. The irony is that years ago when I first bought a Tikka T3 (not T3x) “Tactical”, its stock had an adjustable cheek piece. My CTR models have a separate Picatinny rail base screwed to the top of the receiver, as do the two TAC A1 models I have, as well as a Super Varmint. Other models such as the Ace Target and Ace Game are also pictured with Picatinny rails, and I assume they are also separate parts attached to the receivers rather than the rails being machined into the receiver. I suspect they are made like that so that all receivers are initially the same. “Most men … can seldom accept the simplest and most obvious truth if it … would oblige them to admit the falsity of conclusions … which they have woven, thread by thread, into the fabrics of their lives.” — Leo Tolstoy | |||
|
| Member |
I don't get why anyone would use "beast of a scope" to describe this scope, or why one would not consider it a good option on 6.5cm. My NF is actually heavier and it has no impact on balance. Scopes are literally at the balance point and weight is simply not a material factor on balance. seems like a decent option for the OP. “So in war, the way is to avoid what is strong, and strike at what is weak.” | |||
|
| Ice age heat wave, cant complain. ![]() |
The CTR comes with a pic rail installed from factory, so I'll probably use that. It was a selling point for me over the standard T3x.
Best I can do around here is probably Bass Pro. There may be a shop or two north of me in Apopka or similar, but I'm not familiar with any of them.
You're not far off. Most of my AR practice and training has been traditional carbine stuff. Lately over the past few years I've spent more time proned out. So I'm comfortable in the prone and have an idea of what the rifle should feel like based on my body type.
Thank you! And I appreciate your input. NRA Life Member Steak: Rare. Coffee: Black. Bourbon: Neat. | |||
|
| Member |
That Nightforce scope at 31 ounces weighs more than a half a pound more than a 5-25x56 Z5 Swarovski. A 3.5-18x50 Z5 Swarovski only weighs 18oz. That Nightforce is a BEAST of a scope in comparison! Mind you the Swaro’s are HUNTING scopes and sometimes you WANT a “Beast” of a scope it all depends on what you are doing with it. However if you claim that a heavy scope doesn’t change the balance of a rifle you are simply wrong. If you are in the DFW area perhaps you can drop by some day and I can easily demonstrate the difference to you. I have a half dozen Nightforce scopes up to a 5-25x70mm Zeiss to compare with a good number of Swarovski and other lighter scopes. It takes 2 seconds to feel the difference. If you are target shooting 95% of the time and hunt from a stand 50 yards from where you park a 4 wheeler the extra weight matter little. If you are stalking Elk up and down the Mountains in Colorado an extra pound of scope certainly DOES matter! There’s no good or bad other than picking the wrong Scope for your purpose. Putting a giant scope on a Mountain rifle is just as dumb as putting a 1-4 thick crosshair scope on a 1000yd competition rifle…….dj Remember, this is all supposed to be for fun................... | |||
|
| Member |
The Spuhr one piece mount that I looked at weighs 9 ounces. NF ultralight rings -- the ones I use -- weigh in the ballpark of 3-4 ounces, depending on model. If saving weight is a prime concern, then the 5-6 ounce "beast factor" difference should rule out Spuhr. I don't believe the OP has stated his primary intended use for this rifle. | |||
|
| Member |
You are 100% correct! And you mske a good point. I use Spuhr mounts on tactical and target rifles where I need stout more than light (and when I can afford them). I haven’t tried or weighed their separate rings. The lightweight NF rings are very good. I’ve used more Seekins rings on hunting rifles because they are also lightweight and less expensive. I kinda like the 3rd screw too. Might not make a difference but in my head it’s kind of a failsafe. Appreciate your comment…………Dj Remember, this is all supposed to be for fun................... | |||
|
| Member |
I consider the NF Ultralight rings quite stout. This story goes back a few years, after an extended shooting day with my GAP 308. It had NF Ultralight rings and NF NXS F1 3.5-15x scope at the time. Late in the day, I forgot to close the latches on my Pelican case after shooting. Once home, I grabbed the handle on the case, pulled it from the back of my SUV, and the rifle promptly did a twisting dive to my concrete driveway. Around 16 pounds of rifle dropped close to 2 feet and landed squarely on the left turret -- illumination and parallax. The turret cap shattered and internal pieces went flying. There were small scrape marks on the scope's left side, and on a few sections of the gun's left side. I removed the scope from the rings. Illumination was toast, but parallax seemed to work. Elevation & windage adjustments appeared fine. No damage to the glass. After removing the scope, I had my local 'smith check the rings with a scope alignment bar -- they were still perfectly aligned. I sent the scope to NF for repair. They replaced turret cap and illumination guts. They said everything else was good. The tube was still straight, internals worked fine, glass was undamaged. The repair contact asked if the rings were still good. I said yes; he replied that no damage would have been expected. Once returned from NF, I remounted the scope in the same rings. IIRC, the 100 yard zero required minor tweaking -- maybe 1 MOA or less. I used that scope and those rings on the 308 for a few more years, before I upgraded to a NF ATACR optic. The NF NSX scope is now on a precision AR15, and it works just like it was new. NF Ultralight rings are very strong, and I use only the 4 screw version. | |||
|
| Powered by Social Strata |
| Please Wait. Your request is being processed... |
|
Main Page
The Mason-Howe Rifle Room
Assembling a bolt gun for the first time. Question regarding scope rings REVISED: Rings vs One Piece Mount.
