I have Hogue's on a couple Glocks. Great improvement to get some traction.
I also added a Pachmayr sleeve to my P239 40cal. Adds just the right thickness at the center of the grip.
* * * * * * * High capacity is not an acceptable substitute for good marksmanship.
September 22, 2022, 07:04 PM
Genorogers
quote:
Originally posted by SigSentry: Makes all the difference.
Yeah, they work great on the Ruger LC Series.
September 22, 2022, 08:47 PM
Dakor
Tried one on my Steyr M9-A1 but alas it didn't fit well. The only product from Hogue, which I've purchased that I wouldn't recommend. I think its utility greatly depends on the pistol in question though.
September 23, 2022, 08:08 AM
Sunset_Va
quote:
Originally posted by SigSentry: Makes all the difference.
I have the same pistol, set up the same way. The LC9s is one of my most accurate pistols. The Hogue grip sleeve makes it fit my hand perfectly.
A suggestion: Consider installing a Galloway Precision trigger, I did, to correct trigger sting, but it sure made the trigger better.
美しい犬
September 24, 2022, 10:50 AM
JDSigManiac
Warm it with a hair dryer, then again when you have it half on. It makes it about 80% easier. Have one on my P365 and love it.
September 24, 2022, 04:54 PM
yanici
The Handall Grip just plain works. Very surprise if you don't like it and even shoot better with it on.
John
"Building a wall will violate the rights of millions of illegals." [Nancy Pelosi]
September 24, 2022, 05:31 PM
jeffg
quote:
Originally posted by hi-power man: I have Hogue's on a couple Glocks. Great improvement to get some traction.
I also added a Pachmayr sleeve to my P239 40cal. Adds just the right thickness at the center of the grip.
The Hogue rubber grips make a huge difference on the 239. My friend had the sleeve on his USP and I really liked it but I've never bought one.
September 24, 2022, 09:43 PM
12131
Never been a fan.
Q
September 24, 2022, 10:46 PM
bald1
It was beneficial on my old Kel-Tec P11 which was my only experience with one.
This message has been edited. Last edited by: bald1,
Certifiable member of the gun toting, septuagenarian, bucket list workin', crazed retiree, bald is beautiful club! USN (RET), COTEP #192
October 04, 2022, 05:48 AM
CQB60
Just installed one on a P365. It makes a very good gun even better.
______________________________________________ Life is short. It’s shorter with the wrong gun…
October 04, 2022, 06:28 PM
Chuck Perry
I use one on my Glock 48, improves an already great gun.
October 04, 2022, 06:36 PM
Mustang-PaPa
I have a few but just didn't like them. One of the few things Hogue I don't like.
October 04, 2022, 07:04 PM
birddog1
I have one on my 365 and 365X
October 05, 2022, 04:36 PM
mmurray
So am I to conclude that if you want a little more thickness get the Hogue Handal, but if more thickness isn't needed then perhaps use Talon/skateboard/tread tape?
I've used tape on several guns because I didn't need the grip flats to be "sticky" just the front and back straps, and didn't need any more thickness.
October 07, 2022, 08:49 AM
Eaganite
Just put one on my M&P, was happy when I found out that the factory palm swell is removed and the Houge sleeve takes the place of it. This made the installation substantially easier.
It did change the grip feel alot, looking forward to shooting it. The only negative is a slight gap between the sleeve and the gun frame at the top rear.
I tried to post a picture using my phone and that was impossible for me to figure out.
October 07, 2022, 01:46 PM
smschulz
I use them on all my HK USP's (7 or 8) and on one G19. I like them albeit not the easiest to get on. Improves grip on these weapons dramatically.
October 07, 2022, 02:23 PM
specter77
I found my G48 did not offer the best gripping surface when shooting some loads. Once I installed the Hogue grip sleeve it made all the difference. I put one on a G43 so I knew in advance installation would be "challenging".
This message has been edited. Last edited by: bald1,