Glock disassembly block (roll of duct tape).

September 06, 2021, 04:56 PM

I use a roll of tape as a block to disassemble my Glocks. Seems to be a common thing to use.

My question is if there is an actual product that basically does the same thing? All I've seen are those hockey pucks with holes and grooves drilled into it, and those plastic frames that seems more complex than it needs to be.
basically I would like a nylon or hard rubber cylinder roughly the size and shape of a near empty roll of duct tape. Such product exists? Or should I make a trip to the hardware store instead?

September 06, 2021, 05:04 PM

parabellum

https://www.amazon.com/gp/prod...02_s00?ie=UTF8&psc=1

September 06, 2021, 05:32 PM

Blackwater

I like my APEX block. one side Glock, one side MP.
https://www.apextactical.com/polymer-armorer-block

September 06, 2021, 06:21 PM

sns3guppy

I just use a glock disassembly tool, or in a pinch, a drift. There's nothing on the Glock that takes tapping or force, or that requires a block.

When a roll of duct tape was mentioned, my first thought was a strip of duct tape, stick side up, to keep parts from rolling away. Then it occurred to me that the original poster meant a block with a hole in the middle.

Removing the pins requires fingertip pressure and no more. If its taking more than that, you're not doing it right. That includes the trigger pin, which slides out easily if you work the slide stop a little as you put pressure on the pin.

A block isn't necessary. It doesn't hurt, but the glock easily comes apart and goes back together with just a glock tool and one's hands. It was designed that way.

The only exception I can think of is drifting and unscrewing the sights, or driving the pin out of the trigger bar to put a new shoe on.

September 06, 2021, 06:47 PM

jljones

quote:
Originally posted by Blackwater:
I like my APEX block. one side Glock, one side MP.
https://www.apextactical.com/polymer-armorer-block

I use the APEX.

September 06, 2021, 08:27 PM

Broadside

quote:
Originally posted by sns3guppy:
I just use a glock disassembly tool, or in a pinch, a drift. There's nothing on the Glock that takes tapping or force, or that requires a block.

When a roll of duct tape was mentioned, my first thought was a strip of duct tape, stick side up, to keep parts from rolling away. Then it occurred to me that the original poster meant a block with a hole in the middle.

Removing the pins requires fingertip pressure and no more. If its taking more than that, you're not doing it right. That includes the trigger pin, which slides out easily if you work the slide stop a little as you put pressure on the pin.

A block isn't necessary. It doesn't hurt, but the glock easily comes apart and goes back together with just a glock tool and one's hands. It was designed that way.

The only exception I can think of is drifting and unscrewing the sights, or driving the pin out of the trigger bar to put a new shoe on.

Same here. Never used anything more than a Glock disassembly tool or a punch.

September 06, 2021, 09:55 PM

P220 Smudge

Only tools I have for this task are the backstrap holder thing that has a plastic punch for the frame pins and a Wiha hex driver for the front sight. If the locking block pin doesn’t want to come out, you wiggle the slide lock lever until it comes out easily. That’s not to say you can’t hammer on a Glock, just that it’s completely unnecessary.

September 06, 2021, 10:10 PM

hrcjon

I don't know how the rest of you guys work. But my workshop is filled with detent springs and other misc. stuff that I will never find till I don't need them. It is really convenient and easy to push these glock pins (I didn't say hammer) out into a space where they fall neatly rather than trying to manage them coming out. Just my take.
A block or roll of tape works fine. Both are cheap.

September 06, 2021, 10:18 PM

P220 Smudge

Generally, I push the pins far enough that they're still captive and I pull them the rest of the way out by hand.

September 06, 2021, 10:38 PM

1lowlife

I've never needed anything more than a Glock tool and a piece of newspaper to strip a Glock..
Gen 2 G21 with original black parts.

September 06, 2021, 10:47 PM

YooperSigs

I have a magnetized block I use for everything. Helps keep track of small parts. Cant recall who makes it.

September 07, 2021, 10:27 AM

monoblok

I have several bench blocks that I've acquired over the years but yeah, a roll of masking or painter's tape works reasonably well in a pinch. Less likely to leave sticky tape residue on a receiver like the edge of some duct tape rolls can (ask me how I know).

September 08, 2021, 04:04 PM

Texas Bob C.

I agree with monoblok, I use a roll of painter's tape, a 1.5" wide roll. I cut off a tweaker screw driver and rounded and polished the end to make a pin pusher.

September 08, 2021, 04:09 PM

konata88

Never bought a 'block' but have used a piece of 2x4 to hammer out pins on new glocks. But generally, all I use, like many above, is just the glock tool. And a big plastic bag when working with springs. It's hard finding those little buggers if they get launched. Now I do small spring work inside a plastic bag.

September 08, 2021, 05:32 PM

9mmepiphany

quote:
Originally posted by Blackwater:
I like my APEX block. one side Glock, one side MP.
https://www.apextactical.com/polymer-armorer-block

That is what I use also.

Bought it for the M&P, that it works for the Glock is just a bonus

September 08, 2021, 05:33 PM

9mmepiphany

quote:
Originally posted by Blackwater:
I like my APEX block. one side Glock, one side MP.
https://www.apextactical.com/polymer-armorer-block

That is what I use.

Bought it for the M&P, that it works for a Glock is just a bonus