SIGforum.com    Main Page  Hop To Forum Categories  SIG Pistols    Update on P320 17 round mags and X5
Go
New
Find
Notify
Tools
Reply
  
Update on P320 17 round mags and X5 Login/Join 
Member
posted
I posted a few weeks ago about the 17 round mags not seating in the 320x5. This is after I replaced the floor plates with the updated ones. Still no joy.

I bought a few of the hard use floor plates from Gray Guns and of course the mags pop right in and out.

So there you have it.


NRA Training Counselor
NRA Benefactor Member
 
Posts: 2516 | Location: FL | Registered: May 07, 2009Reply With QuoteReport This Post
Freethinker
Picture of sigfreund
posted Hide Post
Good information to know. Thanks.




6.4/93.6
___________
“We are Americans …. Together we have resisted the trap of appeasement, cynicism, and isolation that gives temptation to tyrants.”
— George H. W. Bush
 
Posts: 47852 | Location: 10,150 Feet Above Sea Level in Colorado | Registered: April 04, 2002Reply With QuoteReport This Post
Member
posted Hide Post
I had the same problem.
Bought X5 Legion base plates to fix.
About the same price as GG.

The budget-minded could sand down the edges of the standard base plate.
 
Posts: 434 | Registered: November 03, 2019Reply With QuoteReport This Post
Member
posted Hide Post
quote:
Originally posted by DirectDrive:
I had the same problem.
Bought X5 Legion base plates to fix.
About the same price as GG.

The budget-minded could sand down the edges of the standard base plate.


So thats the reason for the post. I do not think that would work. I specifically bought the newer base plates, that have the thinner sides.

I do not think any amount of sanding, cutting, etc.. would change that.


NRA Training Counselor
NRA Benefactor Member
 
Posts: 2516 | Location: FL | Registered: May 07, 2009Reply With QuoteReport This Post
Member
posted Hide Post
On my X5 grip module I can see where the interference is with the standard base plates.
It is not much.
I'd wager that someone already has done it, as almost $20 for a baseplate is a bit much.
 
Posts: 434 | Registered: November 03, 2019Reply With QuoteReport This Post
Member
posted Hide Post
quote:
Originally posted by DirectDrive:
On my X5 grip module I can see where the interference is with the standard base plates.
It is not much.
I'd wager that someone already has done it, as almost $20 for a baseplate is a bit much.


Yea. The cost of these things is ridiculous. I bought the BG ones because I love bruce and they are of high quality. But the damn 17 rounders should have just gone in with the standard base plates....


NRA Training Counselor
NRA Benefactor Member
 
Posts: 2516 | Location: FL | Registered: May 07, 2009Reply With QuoteReport This Post
Chilihead and Barbeque Aficionado
Picture of 2Adefender
posted Hide Post
All you have to do is clip the plastic “ears” off the old base plates with wire cutters or a blade, and the mags slip right into an X Five grip frame. It took about five minutes to modify my 17-rd mags. Easy peasy.


_________________________
2nd Amendment Defender

The Second Amendment is not about hunting or sport shooting.
 
Posts: 10564 | Location: FL | Registered: December 29, 2003Reply With QuoteReport This Post
Chilihead and Barbeque Aficionado
Picture of 2Adefender
posted Hide Post
Before and after.



_________________________
2nd Amendment Defender

The Second Amendment is not about hunting or sport shooting.
 
Posts: 10564 | Location: FL | Registered: December 29, 2003Reply With QuoteReport This Post
Member
posted Hide Post
I believe his problem before was with inserting the magazines into the x-frame with the mag well attached.
 
Posts: 6650 | Registered: September 13, 2006Reply With QuoteReport This Post
Member
posted Hide Post
quote:
Originally posted by sns3guppy:
I believe his problem before was with inserting the magazines into the x-frame with the mag well attached.


To be specific. I was trying to insert magazines. With the newer floor plates installed AND the Mag well. Which we know, can not be done.

I appreciate 2ADefender posting that pic. I will say that the gray guns base pads are very nice if not pricey. Your solution is clearly cost effective.

-M


NRA Training Counselor
NRA Benefactor Member
 
Posts: 2516 | Location: FL | Registered: May 07, 2009Reply With QuoteReport This Post
Chilihead and Barbeque Aficionado
Picture of 2Adefender
posted Hide Post
IIRC, when I modified my base plates (maybe a year ago), no one had new ones in stock. So that was my only choice at the time. But it worked just fine.


_________________________
2nd Amendment Defender

The Second Amendment is not about hunting or sport shooting.
 
Posts: 10564 | Location: FL | Registered: December 29, 2003Reply With QuoteReport This Post
Member
posted Hide Post
Pretty much all of us who use older mags and the x-frame do the same thing, clip the dog ears off the mags, but that only allows them to be inserted into the x-frame; it doesn't address the mag well.

With the older style dog ears in (round peg in the base plate), the mag cant' be inserted into the frame at all. Remove the dog ears, the mag slides in. That's without the mag well. The dog ears have no ipact with respect to fitment with the mag well, however.
 
Posts: 6650 | Registered: September 13, 2006Reply With QuoteReport This Post
  Powered by Social Strata  
 

SIGforum.com    Main Page  Hop To Forum Categories  SIG Pistols    Update on P320 17 round mags and X5

© SIGforum 2024