SIGforum.com    Main Page  Hop To Forum Categories  SIG Pistols    Sights for a 210
Go
New
Find
Notify
Tools
Reply
  
Sights for a 210 Login/Join 
Member
posted
Are there any good sights for a P210 standard and/or compact? They come with three dot combat sights, this is not a combat pistol. I have a hard time getting a good sight picture with the three dot stuff. Seams crazy to have a great trigger overcome by poor sights.
 
Posts: 1270 | Location: Northern Nevada | Registered: December 22, 2011Reply With QuoteReport This Post
Member
posted Hide Post
What kind and generation of P210? In any case I think you are talking modern ones? Dawson would be my go to.


“So in war, the way is to avoid what is strong, and strike at what is weak.”
 
Posts: 11259 | Registered: October 14, 2004Reply With QuoteReport This Post
Member
posted Hide Post
I went this route on my standard and have been happy with them.

Trijicon
 
Posts: 253 | Location: Southern, PA | Registered: July 25, 2013Reply With QuoteReport This Post
3° that never cooled
Picture of rock185
posted Hide Post
ACP1, I agree. I see Trijicon lists a black rear and fiber optic front that I believe will fit the 210As, as well as traditional DA/SA SIGs. Haven't checked, but perhaps Dawson or Kensight might have something. I don't care for the 3 dot type either. I went with the target version, black rear, fiber optic front, and adjustable.


NRA Life
 
Posts: 1588 | Location: Under the Tonto Rim | Registered: August 18, 2003Reply With QuoteReport This Post
Member
posted Hide Post
Teach me about the sights that are better than the factory sights. The sights on "Carry" (non-engraved one) seem to be OK - fire with sights alined and hit target right where expected.
What do better sights look like - part numbers?
Thanks.


Mac in Michigan
 
Posts: 508 | Location: Below the Bridge in Michigan | Registered: July 04, 2015Reply With QuoteReport This Post
Member
posted Hide Post
I was similarly insulted by the 3-dots that came set for a "combat sight picture" hold. On a P210, of all things. Ended up with trijicons.
 
Posts: 488 | Registered: February 15, 2004Reply With QuoteReport This Post
Member
posted Hide Post
P320Mac, part numbers are available in the third post in this thread.
 
Posts: 1270 | Location: Northern Nevada | Registered: December 22, 2011Reply With QuoteReport This Post
Member
posted Hide Post
Thanks Metric and acp1 Did not see link. thanks specially for pointing it out. Did not see a reference to P210 on Trijicon's site and most sights seen seem to be very similar to the factory sights on the P210Cary (plan version). I guess that too few P210Cary (plain) were built and sold for augmentations to be expected. Thanks again.


Mac in Michigan
 
Posts: 508 | Location: Below the Bridge in Michigan | Registered: July 04, 2015Reply With QuoteReport This Post
Member
posted Hide Post
The sights on the link are the exact sights that I ordered and put on my P210.

 
Posts: 253 | Location: Southern, PA | Registered: July 25, 2013Reply With QuoteReport This Post
Member
posted Hide Post
SKU: SG701-C-601050All black rear notch and red fiber front sight. I prefer the factory glow-in-the-dark rear and front. I have used fiber front sights in local action competitions and found them to be prone to failure - took two identical pistols so I would have a back up. Valuable information from you about what sights, and their heights, will fit a P210 made in USA. Thanks again. Great pistols.


Mac in Michigan
 
Posts: 508 | Location: Below the Bridge in Michigan | Registered: July 04, 2015Reply With QuoteReport This Post
  Powered by Social Strata  
 

SIGforum.com    Main Page  Hop To Forum Categories  SIG Pistols    Sights for a 210

© SIGforum 2024