SIGforum.com    Main Page  Hop To Forum Categories  SIG Pistols    Grayguns P365XL grip module?
Go
New
Find
Notify
Tools
Reply
  
Grayguns P365XL grip module? Login/Join 
rockchalk06
Member
Picture of rockchalk06
posted
Anyone have one? I just purchased one a few minutes ago. I wanted a new XL grip module anyway, so I figured what the heck.

How tacky is it? Is there a ton of material removed?

Thanks in advance
 
Posts: 1363 | Location: OK | Registered: April 13, 2016Reply With QuoteReport This Post
steve495
Member
Picture of steve495
posted Hide Post
It's subjective as to if you'll like it or not. The general consensus has been that it's "just enough" additional grip without causing clothing to catch or stick to it. I would say there is not a lot of material removed.

Do post here what your opinion is when you receive the module.


Steve

Small Business Website Design & Maintenance - https://spidercreations.net | OpSpec Training - https://opspectraining.com | Grayguns - https://grayguns.com

Evil exists. You can not negotiate with, bribe or placate evil. You're not going to be able to have it sit down with Dr. Phil for an anger management session either.
 
Posts: 5093 | Location: Babcock Ranch, Fla. | Registered: July 18, 2006Reply With QuoteReport This Post
Johnny 3eagles
Bookers Bourbon
and a good cigar
Picture of Johnny 3eagles
posted Hide Post
I don't have the 365XL, but I have 2 of the 365 Laser Sculpted Grip Modules from Grayguns. There isn't much material on the grip module to remove, so sculpting is done without removing depth of the module. The original module was more aggressive, but the sculpted module is more "sticky" (easier to grip and hold on too). The addition of the sculpting in the "thumb rest" area was a big plus for me.

Hope that helps.




Any dog can be a Guide Dog if you don't care where you're going.


NRA ENDOWMENT LIFE MEMBER
 
Posts: 8542 | Location: Arkansas  | Registered: November 06, 2010Reply With QuoteReport This Post
rockchalk06
Member
Picture of rockchalk06
posted Hide Post
quote:
Originally posted by steve495:
It's subjective as to if you'll like it or not. The general consensus has been that it's "just enough" additional grip without causing clothing to catch or stick to it. I would say there is not a lot of material removed.

Do post here what your opinion is when you receive the module.


Thank you. Will do.
 
Posts: 1363 | Location: OK | Registered: April 13, 2016Reply With QuoteReport This Post
rockchalk06
Member
Picture of rockchalk06
posted Hide Post
quote:
Originally posted by Johnny 3eagles:
I don't have the 365XL, but I have 2 of the 365 Laser Sculpted Grip Modules from Grayguns. There isn't much material on the grip module to remove, so sculpting is done without removing depth of the module. The original module was more aggressive, but the sculpted module is more "sticky" (easier to grip and hold on too). The addition of the sculpting in the "thumb rest" area was a big plus for me.

Hope that helps.


Thank you
 
Posts: 1363 | Location: OK | Registered: April 13, 2016Reply With QuoteReport This Post
Draggun
Member
posted Hide Post
I really wish someone would make the grip just a little thicker or somehow add a backstrap. That is my one big complaint with the XL is the grip is so thin, just a tad more grip it would be perfect for me. Shooting a bill drill or at speed in the 20ish splits range, it gets very difficult to handle. Just not much room for my support hand
 
Posts: 178 | Registered: May 16, 2016Reply With QuoteReport This Post
  Powered by Social Strata  
 

SIGforum.com    Main Page  Hop To Forum Categories  SIG Pistols    Grayguns P365XL grip module?

© SIGforum 2026