SIGforum.com    Main Page  Hop To Forum Categories  The Lounge    Cutting porcelain tile with hand held grinder?
Page 1 2 
Go
New
Find
Notify
Tools
Reply
  
Cutting porcelain tile with hand held grinder? Login/Join 
"Member"
Picture of cas
posted Hide Post
I have a friend/employee who does it all the time with a 4" blade on a grinder, he keeps water flowing on it with a large sponge.

Of course he's a tile guy and did it daily for many many years. So it can be done, but how well a novice might do is another issue.


_____________________________________________________
Sliced bread, the greatest thing since the 1911.

 
Posts: 21501 | Location: 18th & Fairfax  | Registered: May 17, 2003Reply With QuoteReport This Post
Too old to run,
too mean to quit!
posted Hide Post
quote:
Originally posted by arcwelder76:
If you can bury the cuts under baseboard or some other overlap, a hand held grinder with a diamond wheel will be fine. It does take some hand strength though.

You can use some clamps and some wood to make a rail for you to run the grinder along and make very straight cuts.

I/we have done a LOT of tile work. Kitchen floors, counters, bathroom floors, etc.

For that kind of work you really need a real tile saw. Since what I understand your project to be, on of those blades in an angle grinder would do it, just fine. Clamp a piece of wood to use as a guide for the blade, go slow and it should work out well. And be careful with that angle grinder!

It can be done.


Elk

There has never been an occasion where a people gave up their weapons in the interest of peace that didn't end in their massacre. (Louis L'Amour)

"To compel a man to furnish contributions of money for the propagation of opinions which he disbelieves and abhors, is sinful and tyrannical. "
-Thomas Jefferson

"America is great because she is good. If America ceases to be good, America will cease to be great." Alexis de Tocqueville

FBHO!!!



The Idaho Elk Hunter
 
Posts: 25656 | Location: Virginia | Registered: December 16, 2001Reply With QuoteReport This Post
Happily Retired
Picture of Bassamatic
posted Hide Post
We recently replaced our backsplash tile (not a real big job) and the tile guy used a hand held grinder for his cuts. He was quick and accurate with it and we are very pleased.



.....never marry a woman who is mean to your waitress.
 
Posts: 5186 | Location: Lake of the Ozarks, MO. | Registered: September 05, 2005Reply With QuoteReport This Post
Member
posted Hide Post
2 concerns

the grinder will have a lot of torque when turned on, be aware of the angle of the blade starting the cut. think about a gyroscope while trying to align the blade to the cut.

and

OSHA prohibits cutting ceramic tile without means to control the silica dust. not that you will be in front of a compliance officer while you work in your house, but there will be a lot of fine dust from the cuts. keep the cutting outside to prevent cleanup issues inside.

ymmv
john
 
Posts: 476 | Location: Greensboro, NC | Registered: November 26, 2009Reply With QuoteReport This Post
Member
Picture of wrightd
posted Hide Post
if you use a grinder instead of wet saw is there risk of breathing bad stuff related to silicosis ?

http://elcosh.org/document/193...-risky-business.html

at least wear an approved sealing particulate mask, not one of those rubber band masks.




Lover of the US Constitution
Wile E. Coyote School of DIY Disaster
 
Posts: 9087 | Location: Nowhere the constitution is not honored | Registered: February 01, 2008Reply With QuoteReport This Post
Facts are stubborn things
Picture of armedprof
posted Hide Post
I did my bathroom floor. Started with the grinder, went and bought a tile cutter. They are not that expensive but work a lot better than the grinder. That said, the grinder works but makes a mess.





Do, Or do not. There is no try.
 
Posts: 1804 | Location: Just South of Charlotte, NC | Registered: February 24, 2011Reply With QuoteReport This Post
Member
posted Hide Post
have seen someone put a diamond blade on a skillsaw- that may be a way for you to get straighter lines. I just did 1200 sf of tile, and used a small wet saw for most of the cross cuts, rented a big saw for the rips- 44" tiles are hard to rip, and the angle grinder with the diamond blade had its use too- especially cutting the tiles to go around the toilet flange, and some doorways where I could not slide tile under the trim.


There is something good and motherly about Washington, the grand old benevolent National Asylum for the helpless.
- Mark Twain The Gilded Age

#CNNblackmail #CNNmemewar
 
Posts: 706 | Location: Seacoast in USA | Registered: September 24, 2007Reply With QuoteReport This Post
I'd rather have luck
than skill any day
Picture of mjlennon
posted Hide Post
Agree, tile saw way to go. HF has on starting at $67. Wet saw

Be sure to post some pics of the project.
 
Posts: 1858 | Location: Fayetteville, Georgia | Registered: December 08, 2005Reply With QuoteReport This Post
Green grass and
high tides
Picture of old rugged cross
posted Hide Post
I just cannot imagine something like that lasting much past the first cut on a super hard porcelain tile. If that.



"Practice like you want to play in the game"
 
Posts: 19950 | Registered: September 21, 2005Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2  
 

SIGforum.com    Main Page  Hop To Forum Categories  The Lounge    Cutting porcelain tile with hand held grinder?

© SIGforum 2024