SIGforum.com    Main Page  Hop To Forum Categories  What's Your Deal!    Getting power run to an outbuilding - what a hassle.
Page 1 2 
Go
New
Find
Notify
Tools
Reply
  
Getting power run to an outbuilding - what a hassle. Login/Join 
PHPaul
Three Generations
of Service
Picture of PHPaul
posted Hide Post
This is becoming a Tesla my patience.



Be careful when following the masses. Sometimes the M is silent.
 
Posts: 15635 | Location: Downeast Maine | Registered: March 10, 2010Reply With QuoteReport This Post
Patrick-SP2022
On the wrong side of
the Mobius strip
Picture of Patrick-SP2022
posted Hide Post
You are dealing with the electric company, resistance is futile.
I’d be close to pulling the plug on the project.



 
Posts: 4174 | Location: Texas | Registered: April 16, 2012Reply With QuoteReport This Post
trapper189
Savor the limelight
posted Hide Post
Watts you needs to do is meditate.

Ohm, Ohm, Ohm
 
Posts: 11981 | Location: SWFL | Registered: October 10, 2007Reply With QuoteReport This Post
joel9507
Don't Panic
Picture of joel9507
posted Hide Post
quote:
Originally posted by PHPaul:
quote:
Originally posted by Krazeehorse:
Can't bury?


Pole to building is "free". Buried, I have to buy the wire. Direct burial wire for 100 amp service over 200 feet is seriously expensive.

Due to heat dissipation issues, direct burial wire is larger gauge than free air for the same rating.

Plus, of course, the cost of digging and back-filling the trench.

OTOH....when the winds blow, ice/snowstorms hit, and power goes out ...instead of scrambling, and trying to get techs out in the midst of widespread service outages....you'd be inside, all warm and toasty, sipping cocoa......

Might balance the cost thing a tad?
 
Posts: 15234 | Location: North Carolina | Registered: October 15, 2007Reply With QuoteReport This Post
HRK
Thank you
Very little
Picture of HRK
posted Hide Post
with any luck the power company will surge forward with the project
 
Posts: 24656 | Location: Gunshine State | Registered: November 07, 2008Reply With QuoteReport This Post
frayedends
paradox in a box
Picture of frayedends
posted Hide Post
Electrons have consequences.



These go to eleven.
 
Posts: 12605 | Location: Westminster, MA | Registered: November 14, 2006Reply With QuoteReport This Post
SigSAC
Member
posted Hide Post
You'll find a way to power through the process.
 
Posts: 2835 | Location: Northern California | Registered: December 01, 2006Reply With QuoteReport This Post
mojojojo
Happiness is
Vectored Thrust
Picture of mojojojo
posted Hide Post
I think if you took a survey most people would volt for going with the pole option.

But you should probably take a breaker from these electric puns and focus on the project. Delaying too long could be terminal.


Icarus flew too close to the sun, but at least he flew.
 
Posts: 6787 | Location: North Carolina | Registered: April 30, 2003Reply With QuoteReport This Post
OKCGene
Dances With
Tornados
posted Hide Post
Ah you really don't need an electric pole.

Come on, admit it, you're really talking about a new Stripper Pole in your workshop.

(I'll send the beer over)
.
 
Posts: 12063 | Location: Near Hooker Oklahoma, closer to Slapout Oklahoma | Registered: October 26, 2009Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2  
 

SIGforum.com    Main Page  Hop To Forum Categories  What's Your Deal!    Getting power run to an outbuilding - what a hassle.

© SIGforum 2024