Main Page
Disaster & Survival Preparedness
Portable Communications Kit using SDR, HAM/GMRS, MeshCore - No infrastructure needed except a power source.Go ![]() | New ![]() | Find ![]() | Notify ![]() | Tools ![]() | Reply ![]() | |
Told cops where to go for over 29 years…![]() |
I was originally going to post this in the thread I started on MeshCore, but the thread didn’t seem to get much attention and this goes well beyond basic MeshCore, combining these elements into a more in depth off-grid comm system should the need arise. MeshCore - text based messaging Software Defined Radio (SDR) - Extreme wide band, computer controlled radio receiver to find and listen to radio transmissions HAM Radio - Classic communications tool for Transmit and Receive, SDR compliments the HAM radio by quickly identifying active frequencies for use. For those unfamiliar with MeshCore, here is a graphic on how the Mesh works. MeshCore radios are low cost ($30-70) and connect to a phone or tablet app to send and receive text messages. No internet/cellular connection required (once app is installed), just BT between radio and device. I’m two months into my MeshCore odyssey and am really impressed with the tech. The Mesh is very active in my area and I hear (well, actually “read”) a lot more traffic on it than on my 2m/70cm HAM or DMR radios. Originally I bought two radios, Elecrow M1 and M5. They are nice well made “out of the box” radios that bounce between $65 and $75 each on Amazon. After having ChatGPT compare them as well as other options I ended up returning the M5. Basically the same features, M5 had a more robust processor and onboard memory (at the cost of battery life). The M1 is more power efficient with longer battery life, and MeshCore doesn’t take advantage of the stronger processor/memory. After learning more, and more ChatGPT discussion, I decided to return the M1 as well in favor of a couple of Helvec V4.3 radio “kits” - just plugging connectors together and putting into a case, no soldering or anything complex required. Set of two was less than $95 and take about 10 minutes to assemble. Not quite as “polished” as the Elecrow models but they have 3000mAh batteries instead of 1200mAh and are capable of about 5x the output power for transmitting. Have had some growing pains and am still learning. I find it all interesting and it is good brain exercise for tech stuff. I also recently picked up an RTL-SDR radio receiver dongle which is something I’ve been wanting to get for a while now. For those unfamiliar, it is like a super-wide band “scanner” of the RF spectrum. Mine will cover 100Khz to 1.75Ghz, it plugs into a computer, attach appropriate antenna and a computer controls the reception frequency, modulation, and decoding the audio (regular analog signals). One benefit of the SDR is it visually show a wide “slice” of spectrum at one time instead of scanning individual frequencies. You can select a frequency that shows an active transmission to hear the message, or with the frequency identified, tune you HAM radio to same for transmit or receive. With the new tech came a new idea and a new problem… The idea - Combine the two technologies into a single portable “kit” for SHTF communications. The problem - MeshCore is already pretty mobile by design. My use of it at home however, has a weakness - For best TX/RX, my Mesh radio is placed upstairs and the BLE (Bluetooth Low Energy) connection gets a little spotty when I am in other areas of the house. SDR dongle needs to be connected to a computer (won’t work on an iPad) and you have the antenna to deal with as well. At home my desktop computer is in an upstairs bonus room. Most of my time is spent elsewhere in the house, usually downstairs with my wife. Therein lies the problem. I can Mesh wherever, but risk losing connection between iPad and radio due to separation. To use the SDR I would need to be in the “office” tied to the computer where everything else is set up. So I got to thinking, what if there was a way to have the computer running the SDR dongle as well as manage the interface to the Mesh radio, and then let me access either (or both) over home WiFi from my iPad anywhere in the house? “Hey ChatGPT can this be done?” Why yes it can! MeshCore Remote Terminal runs on a computer and takes the place of the MeshCore mobile app for managing the Mesh radio as well as handling RX/TX messaging. SDR software runs on the same computer, and then those apps can be viewed and controlled on the iPad via web-based remote access or more specifically “accessing self-hosted web applications over your local network (LAN)”. Since the whole point of this stuff for me is “SHTF” scenario, I wanted a “portable” solution that was not dependent on internet or infrastructure. My desktop computer would be overkill and is not exactly portable. Additionally, I wouldn’t to want to leave it running 24/7 for those applications. While a laptop might seem like the obvious answer, for what I envisioned, it creates a limitation of being AT the computer for operation. I like the idea of being able to move freely around my location carrying only the iPad, while leaving the remaining hardware in place. Enter the Raspberry Pi computer… After some pretty reasonable low cost equipment purchases (4gb Raspberry Pi 5 computer board, Pwr Supply, Case = $148) along with a MicroSD card I already had and lots of back and forth with ChatGPT, I was able to get my Raspberry Pi up and running. No monitor, keyboard, or mouse needed. Just a remote terminal connection through the “Termius” app on my iPad. Next up, getting the MeshCore remote terminal installed, running, and connected to my Helvec V4 radio. Some more ChatGPT stepping me through all the Linux commands via iPad and Termius to make that happen, and it was up and running. Similar process to install “OpenWebRX” a free SDR control program to manage the RTL-SDR dongle. With everything running, I open either of those on my iPad and run as a web app using Safari. Ok, it’s working but reliant on my home WiFi network. What about the “portable” part if I have to operate remote? ChatGPT stepped me through the process of setting up the Pi to act as a “Hot Spot” creating it's own WiFi network. On startup, if it is unable to connect to my home network within 90 seconds, it goes into Hot Spot mode. Then I connect my iPad to the Pi’s WiFi and everything works just the same, off grid, no internet or cellular needed, just a power source for the Pi and a means to keep the iPad and Mesh radio charged. Pretty impressed with how it all turned out. In the coming week I will be packing it all into a small case and heading out to try it remotely in Hot Spot mode. Here is an overview of how it all works together… What part of "...Shall not be infringed" don't you understand??? | ||
|
| Powered by Social Strata |
| Please Wait. Your request is being processed... |
|
Main Page
Disaster & Survival Preparedness
Portable Communications Kit using SDR, HAM/GMRS, MeshCore - No infrastructure needed except a power source.
