|Quit staring at my wife's Butt|
I'm starting to like the .380 round, thought maybe I would give it a try since it cost about 18 dollars a box for blazer brass. I currently load 9 mm and .357 sig out of my 650, looks like I will need a conversion kit and some dies.
How many are also doing this cartridge? any help would be great.
I load for two LCP's and my P238. Of course the P238 is the most pleasant to shoot, but LCPs have their place.
My plinking rounds are 90 grain plated RN. The more carry type are Gold Dot bullets.
My favorite powder for the 380 is Win 231(HP-38). One will see it mentioned again & again in the reloading manuals.
I have loaded a shit load of that on the 550.
Can be painful on setting bullet on that case,when you got fat fingers
I have been loading 380 brass for a long time now. I have two different loads.
(1) a near min. load for my blowback 380 handguns. It makes shooting them much more comfortable.
(2) a full factory equivalent load for my locked breech 380 handguns.
I load either 95gr RN FMJ, or plated 100gr RN bullets. They both work just fine for me.This message has been edited. Last edited by: GT-40DOC,
|The Unmanned Writer|
I bought a P232 when the wife and i were dating. While dating i only shot it a few times expecting it to be my summer carry.
Since getting married I've shot it a lot more with the wife.
I really did like that gun and wish they were still being produce.
Sentiment without action is the ruin of the soul.
Help, I'm having premonitions of future flashbacks.
Only in an insane world are the sane considered insane.
Some people listen to the noise of the world,
And some people listen to the quiet.
I have load a lot of rounds, its a great round to shoot.
Colt .380 Gov't, Bersa Thunder .380, and two Sig P238's. Since I don't shoot a lot of .380 ammo I choose one load that performs well in them all. I prefer Hornady 90 gr. XTP-hp with AA#2 powder at near maximum from Accurate's web site using CCI 500 primers. My AA#2 load shoots the same as factory Hornady 90 XTP. I load on single stage presses and prefer Hornady's .380 die set with the sliding alignment sleeve seating die. Takes the tiny bullets from your finger and guides it into the case. I also have an RCBS set that's excellent. Don't know how the Hornady seater would work in progressive press? I usually carry with Hornady Custom .380 or American Gunner 380. My 90gr.XTP handload shoot to same point of impact as factory and makes things simpler than various bullets and weight for plinking and another for carry.
Have loaded hundreds of .380 with a 95 gr. FMJ and a medium amount of Universal.
I don't shoot my 380's a lot, the most reloading for them I do is my 380 shotshells, I use on snakes.
My least favorite round to reload. It's not bad if you on a AP where you don't have to handle the small cases. But on a SS it's a pain. Then you dealing with a charge weight that may only have a spread of 0.3gr. Not much room for error. Othe4r than that it loads just like any other cartridge.
P229R 9mm, Nitron, Beavertail Frame, Night Sights, DA/SA, SRT & Short Reach Trigger
I just got a Beretta 84, and looking at the cost of .380, am starting to think about reloading. What sort of equipment investment am I looking at? If I shoot 100-200 rounds per month, then I'd like to know how cost effective it would be.
I also have 5 kids, so a setup that is massively labor intensive is kind of out of the question.
There is something good and motherly about Washington, the grand old benevolent National Asylum for the helpless.
- Mark Twain The Gilded Age
See the stickys above.
|Powered by Social Strata|