SIGforum.com    Main Page  Hop To Forum Categories  Mason's Rifle Room    Sig 556 Quad Rail removal.
Go
New
Find
Notify
Tools
Reply
  
  Login/Join 
Sid
Member
Posted
I've been trying the last hour looking to see if there's some sort of retainer holding the lower half of the Quad Rail from sliding toward the upper receiver and down off the upper half of the said rail.

I've got the upper receiver detached from the lower with the forward retaining screw and its shroud completely removed.

I'm about close to taking a hammer to the rail to slam it down.

Is there something I'm doing wrong?


-Sid

====================

Freedom is not free.
 
Posts: 69 | Registered: January 16, 2009Reply With QuoteEdit or Delete MessageReport This Post
Member
Posted Hide Post
If I remember correctly, you need to remove the FRONT RETAINING PIN that holds the upper and the lower together....

Jim


Sig 229R .40 NK w/ Elite Grips
Sig 226 9mm 'JJ' West German
AZ Armory AR15 Carbine with Troy and Magpul Accessories.
Kahr P9
 
Posts: 64 | Location: Phoenix! When not on the Road... | Registered: November 02, 2007Reply With QuoteEdit or Delete MessageReport This Post
Sid
Member
Posted Hide Post
Yes, I've done that, but described it as the forward retaining screw/pin and its shroud/pin (where the threaded "pin" screws into). One removed from the right side, the other removed from the left.

The upper receiver and lower are completely detatched.

On close inspection, there's evidence of forced fitting of the lower quad rail. I'm seeing the protective coating where the lower rail's rear pin hole seats all scraped off as metal on metal were forced together.

This is not good news.


-Sid

====================

Freedom is not free.
 
Posts: 69 | Registered: January 16, 2009Reply With QuoteEdit or Delete MessageReport This Post
Sid
Member
Posted Hide Post
quote:
Originally posted by JimbobAZ:
If I remember correctly, you need to remove the FRONT RETAINING PIN that holds the upper and the lower together....

Jim


Jim, do you mean the front retaining pin that holds the upper and lower RECEIVERS together? Or another pin I'm unaware of that holds the upper and lower RAILS together?


-Sid

====================

Freedom is not free.
 
Posts: 69 | Registered: January 16, 2009Reply With QuoteEdit or Delete MessageReport This Post
Member
Posted Hide Post
Reverse the installation instructions with a large nylon hammer present. Cool
 
Posts: 1358 | Location: Here, when I posted this | Registered: January 27, 2001Reply With QuoteEdit or Delete MessageReport This Post
Sid
Member
Posted Hide Post
quote:
Originally posted by MitchbSC:
Reverse the installation instructions with a large nylon hammer present. Cool


Thank you much, Mitch!

Seems my lower Quad Rail was forced into position and will not budge. I've gone so far as to take a wood spacer and hammer it loose, but no luck.

I'm wondering if everyone's quad rail was this difficult to remove or is it just my rifle.


-Sid

====================

Freedom is not free.
 
Posts: 69 | Registered: January 16, 2009Reply With QuoteEdit or Delete MessageReport This Post
Member
Posted Hide Post
Sid, you have apparently not made your sacrifice to the rail gods. Once you put enough pressure on it it WILL eventually break loose and take a good chunk of skin with it. After that you will be able to get it on and off regularly.

At least, that was my experience.

Mark
 
Posts: 500 | Location: middle Tennessee | Registered: October 28, 2008Reply With QuoteEdit or Delete MessageReport This Post
Member
Picture of Mr Wild Bill
Posted Hide Post
Can anybody say "tetanus shot"? Eek


Must buy, must buy, must buy....
 
Posts: 218 | Location: Frostbite Falls MN | Registered: December 29, 2006Reply With QuoteEdit or Delete MessageReport This Post
  Powered by Eve Community  
 

SIGforum.com    Main Page  Hop To Forum Categories  Mason's Rifle Room    Sig 556 Quad Rail removal.

© SIGforum 2009