SIGforum.com    Main Page  Hop To Forum Categories  SIG Pistols    A 5 weeks 10,000 rounds report on a Klein Ni P228 - Lots and lots of pics. /// ** 20k ** (p.4) /// *** RIP @ 25k *** (p.6)
Page 1 2 3 4 5 6 7 8 9 
Go
New
Find
Notify
Tools
Reply
  
A 5 weeks 10,000 rounds report on a Klein Ni P228 - Lots and lots of pics. /// ** 20k ** (p.4) /// *** RIP @ 25k *** (p.6) Login/Join 
Oriental Redneck
Picture of 12131
posted
I had great fun putting this gun through the wringer.

Gun: A factory Nickel P228, serial # B152251, mint condition unfired by previous owner. Still looks outstanding, but it's now no longer mint.

Test: 10,000 rounds in 5 weeks (12/28/18 - 1/30/19)

Lubrication: Slip2000 EWL30 and EWL first 3750 rds; EWL30 exclusively after that.

Mags used: Mostly Mec-Gars, a few Germans, and a single Checkmate.

Ammo used:

Blazer Brass 115 FMJ = 2000 rds
Blazer Brass 124 FMJ = 300 rds
Fiocchi 115 FMJ = 500 rds
Fiocchi 124 XTPHP = 50 rds
Geco 115 FMJ = 2700 rds
Geco 124 FMJ = 1000 rds
Sellier & Bellot 115 FMJ = 2000 rds
Speer Lawman 115 TMJ = 950 rds
Speer Gold Dot 124 GDHP = 150 rds
Federal Hi-Shok 115 JHP = 150 rds
Federal HST 147 JHP = 150 rds
Remington Golden Saber 124 +P BJHP = 50 rds

Range sessions:

#01- 12/28/18 - 200 rds
#02- 01/02/19 - 400 rds
#03- 01/04/19 - 400 rds
#04- 01/05/19 - 500 rds
#05- 01/08/19 - 500 rds
#06- 01/10/19 - 500 rds
#07- 01/11/19 - 500 rds
#08- 01/15/19 - 750 rds
#09- 01/16/19 - 250 rds
#10- 01/17/19 - 500 rds
#11- 01/18/19 - 500 rds
#12- 01/19/19 - 400 rds
#13- 01/20/19 - 600 rds
#14- 01/22/19 - 600 rds
#15- 01/23/19 - 600 rds (50 are HP)
#16- 01/24/19 - 600 rds
#17- 01/25/19 - 600 rds
#18- 01/26/19 - 600 rds
#19- 01/29/19 - 500 rds (all HP)
#20- 01/30/19 - 500 rds

Distances: 10 & 15 yds.

Cleaning: From round #6001 to round #10,000, the gun was left uncleaned (not even a wipe down). Only added was some more EWL30 at the beginning of each range trip. And, it finally got its overdue clean up after the last range trip.

Malfunctions: One. Round #9390 (a Federal HST 147 HP) got hung up on the feed ramp. A quick rack of the slide, and it went right in chamber.

Conclusions/Observations:
- Nothing was replaced during the entire testing. Except for the grips, everything is original from start to finish.
- Can't speak for any other guns, but this particular gun is impressive.
- First session - the gun had the aluminum grips on, and they immediately became loose.
- So, grips were changed to G10 for the rest of the sessions, with blue Loctite to secure the grips. They were pretty good, but as the sessions went on, the screws still worked themselves loose.
- Guns gets extremely hot during mag dump sessions, as you can imagine. I got blisters a couple of times.
- The blued barrel resists wear better than I had expected. The lube must have helped quite a bit.
- There is some flaking on the left side of the chin of the slide and on its undersurface.
- Because it’s slicker, the nickel gun is easier to clean. Also, with a white gun, it’s just easier to spot a dirty spot, even when it’s hidden in cracks/corners/crevices.

Plan: This first phase is over. The next phase will be less volume and longer term, with reports back from time to time. The main reason I started this whole process is really to see how the stripped factory anodized frame that has been Nickel plated will hold up over time.



Enjoy the pics. Cool

Barrel smileys from zero to 10,000








From 6001 to 10,000, the gun was not cleaned, so the barrel was dirty. So, pics are not included here.



Gun at the start and at finish















































Some other fun pics in between
















This message has been edited. Last edited by: 12131,


Q






 
Posts: 26205 | Location: TEXAS | Registered: September 04, 2008Reply With QuoteReport This Post
Member
Picture of Redhookbklyn
posted Hide Post
Well reported, sir. Look forward to phase 2.

Thank you for sharing.



“There is love in me the likes of which you’ve never seen. There is rage in me the likes of which should never escape."
—Mary Shelley, Frankenstein

 
Posts: 1925 | Location: South Carolina  | Registered: January 01, 2014Reply With QuoteReport This Post
Member
posted Hide Post
what a great report + pics, thanks q.
 
Posts: 2207 | Registered: October 17, 2013Reply With QuoteReport This Post
Member
Picture of JBird679
posted Hide Post
Damn! It cleaned up nicely after that torture test!

How much did your accuracy and recoil sensitivity improve after shooting that many rounds in such a short time? I hope you went for accuracy once in a while.
 
Posts: 987 | Location: Upstate, SC | Registered: March 19, 2008Reply With QuoteReport This Post
Freethinker
Picture of sigfreund
posted Hide Post
A very impressive performance—by both the gun and the shooter!




6.4/93.6

“Wise men talk because they have something to say; fools, because they have to say something.”
— Plato
 
Posts: 47366 | Location: 10,150 Feet Above Sea Level in Colorado | Registered: April 04, 2002Reply With QuoteReport This Post
Member
Picture of Greymann
posted Hide Post
Originally posted by sigfreund:
A very impressive performance—by both the gun and the shooter!
.............................................

To Hell and Back Reliability!
 
Posts: 1540 | Location: New Mexico | Registered: March 21, 2017Reply With QuoteReport This Post
7.62mm Crusader
posted Hide Post
That is amazing Q. The hammer face is still intact. Eventually, the slide bore begins to dig in deeper and the smilies become a displacement of metal. Seen some Sigs with a fair amount of depth to the smiley area. Also, atop the large diameter of its barrel, just forward of its chamber there is a small progression of that little flat spot. The lube stayed put just nicely. I bet the trigger finger is tired. The nickle held up well. The whole guns parts functioned together beautifully. This is proof one doesn't have to be afraid to shoot their collectable guns.
 
Posts: 17891 | Location: The Bluegrass State! | Registered: December 23, 2008Reply With QuoteReport This Post
Member
Picture of GataGunner
posted Hide Post
Did you replace any springs or the breech block roll pin along the way?
 
Posts: 64 | Registered: January 25, 2019Reply With QuoteReport This Post
Avoiding
slam fires
Picture of 45 Cal
posted Hide Post
Wow that is impressive.
I would have thought there would have been more ware on the firearm.
 
Posts: 22407 | Location: Georgia | Registered: February 19, 2007Reply With QuoteReport This Post
Member
Picture of Nframe
posted Hide Post
That is great Q!!

My son's M11-a1 is up over 6K but it has taken years and we did replace the recoil spring. These guns sure do well!

Thanks for the write up!
 
Posts: 2912 | Location: mid S.C. | Registered: March 22, 2006Reply With QuoteReport This Post
Member
Picture of huskerlrrp
posted Hide Post
Very interesting. Thanks for documenting and sharing. I see you lubricate well, that gun looks better than some I've seen with a fraction of the rounds fired.


 
Posts: 1788 | Location: North Cackalacky | Registered: September 09, 2007Reply With QuoteReport This Post
Member
posted Hide Post
Thanks Q, very impressive. That takes some dedication. Would you agree that this backs up the claim of
"To hell and back" reliability"?
 
Posts: 312 | Location: Ohio | Registered: January 04, 2015Reply With QuoteReport This Post
Knows too little
about too much
Picture of rduckwor
posted Hide Post
Heroic effort in so many aspects of that word. Thanks for the info and pictures.

So after 10K rounds, what is your assessment of the frame status?

thanks,

RMD




TL Davis: “The Second Amendment is special, not because it protects guns, but because its violation signals a government with the intention to oppress its people…”
Remember: After the first one, the rest are free.
 
Posts: 20303 | Location: L.A. - Lower Alabama | Registered: April 06, 2008Reply With QuoteReport This Post
It's all part of
the adventure...
posted Hide Post
That’s very cool! It would have been very difficult for me to resist the urge to clean it when it started looking nasty, but I totally understand why you did it.


Regards From Sunny Tucson,
SigFan

NRA Life - IDPA - USCCA - GOA - JPFO - ACLDN - SAF - AZCDL - ASA

"Faith isn't believing that God can; it's knowing that He will." (From a sign on a church in Nicholasville, Kentucky)
 
Posts: 1677 | Location: Tucson, Arizona | Registered: January 30, 2000Reply With QuoteReport This Post
Grapes of Wrath
Picture of Wino
posted Hide Post
Thanks for posting and sharing your observations!
 
Posts: 1454 | Location: Texas | Registered: March 09, 2005Reply With QuoteReport This Post
Member
Picture of Tooky13
posted Hide Post
Very impressive the way the nickel held up after $1,700+ worth of ammo Cool


We the people are the rightful masters of both Congress and the courts, not to overthrow the Constitution but to overthrow the men who pervert the Constitution.
Abraham Lincoln
 
Posts: 1307 | Location: Scottsdale, Arizona | Registered: December 07, 2013Reply With QuoteReport This Post
A day late, and
a dollar short
Picture of Warhorse
posted Hide Post
Well done Q!

I'd say that dispels the myth that removing the anodizing and nickel plating, weakens the alloy frame.


____________________________
NRA Life Member, Annual Member GOA, MGO Annual Member
 
Posts: 13668 | Location: Michigan | Registered: July 10, 2004Reply With QuoteReport This Post
Member
posted Hide Post
Great pics and documentation Q. Best thread ever!!
 
Posts: 1063 | Location: hampton roads, va. | Registered: October 03, 2002Reply With QuoteReport This Post
Shall Not Be Infringed
Picture of nhracecraft
posted Hide Post
Heck of a 'Break-in' procedure! Cool


____________________________________________________________

If Some is Good, and More is Better.....then Too Much, is Just Enough !!
Trump 2024....Save America!
"May Almighty God bless the United States of America" - parabellum 7/26/20
Live Free or Die!
 
Posts: 8787 | Location: New Hampshire | Registered: October 29, 2011Reply With QuoteReport This Post
I'm Pickle Rick!
Picture of Pickle Rick
posted Hide Post
Thanks Q, that was a very comprehensive evaluation. What I find amazing is that after cleaning ? The barrel shows minimal wear (smileys) and the face of the hammer though not extreme shows very little wear otherwise it still looks new. I honestly didn't know that nickel was so sturdy. WOW. John.


______________________________
" Formally known as GotDogs "
 
Posts: 2862 | Location: Lancaster, PA. | Registered: February 06, 2007Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2 3 4 5 6 7 8 9  
 

SIGforum.com    Main Page  Hop To Forum Categories  SIG Pistols    A 5 weeks 10,000 rounds report on a Klein Ni P228 - Lots and lots of pics. /// ** 20k ** (p.4) /// *** RIP @ 25k *** (p.6)

© SIGforum 2024