SIGforum.com    Main Page  Hop To Forum Categories  The Lounge    Recommendations 1/2” air impact wrench for home mechanic
Page 1 2 

Moderators: Chris Orndorff, LDD
Go
New
Find
Notify
Tools
Reply
  
Recommendations 1/2” air impact wrench for home mechanic Login/Join 
Member
posted
Guys, looking for recommendations for 1/2” impact wrench. My son was in town for Thanksgiving and we did an impromptu wheel bearing replacement on his Subaru. Sadly my Craftsman 1/2” didn’t have the juice to break the stabilizer bolt. Borrowed my neighbor’s Mac impact and it did the trick. My research shows my Craftsman is rated at 400# while the Mac is likely over 1000#. My air compressor (240v) is rated at 10.2 SCMF at 90#, so I think I’m OK for most 1000# wrenches quick trend around 8 SCMF.

Internet search shows preference for Aircat, Nitrocat and Chicago Pneumatic. I’m d like to stick under $200. I don’t think I need to spend $250-300 for SnapOn or Mac. I won’t use it too much.

Thanks for your input.


P229
 
Posts: 2871 | Location: Sacramento, CA | Registered: November 21, 2008Reply With QuoteReport This Post
His diet consists of black
coffee, and sarcasm.
Picture of egregore
posted Hide Post
I have used an Aircat 1150 every day and hard for over three years, which is probably a lifetime of your intended use. It has done everything I have asked of it, including Honda crankshaft pulley bolts. https://www.amazon.com/AIRCAT-...TG9nQ2xpY2s9dHJ1ZQ== I assume you have an adequate air compressor to run it.
 
Posts: 22879 | Location: Johnson City/Elizabethton, TN | Registered: April 28, 2012Reply With QuoteReport This Post
Member
Picture of Beancooker
posted Hide Post
I understand wanting to keep it under $200, but if you can get a snap on or Mac fir $50 more, it’s probably money well spent.

Not sure if they even make them anymore, but one of the guys at a shop I used to frequent in Washington, PIA (Pacific Import Auto) had a few Ingersoll Rand impacts. You had to stop way short and use a torque wrench in order to not shear off bolts. They were damn old and still the powerhouses of the shop.

These: 1300 ft/lb nut busting torque.




quote:
Originally posted by Balzé Halzé:
Before I figured you were just confused, but now I see that you're about as bright as a black hole, and twice as dense. Good lord.

The “lol” thread
 
Posts: 1262 | Location: Staring down at you with disdain, from the spooky mountaintop castle.  | Registered: November 20, 2010Reply With QuoteReport This Post
Raised Hands Surround Us
Three Nails To Protect Us
Picture of Black92LX
posted Hide Post
My Ingersol Rand has been thumping just fine for over a decade now.


--------------------------------------
Everybody’s got a blank page. A story they’re writing today. A wall that they’re climbing. You can carry the past on your shoulders.
Or you can start over.
Regrets, no matter what you goin’ through. Jesus, He gave it all to save you. He carried the cross on His shoulders. So you can start over.
~NF RealMusic~
 
Posts: 20937 | Registered: September 06, 2003Reply With QuoteReport This Post
Member
posted Hide Post
Ingersoll Rand IR231. I've had one for years and the first several were daily use. It's never let me down. They can be had for about $130.00. Anything in the 1,000 lb./ft. range would probably be overkill for home use unless you're working on big tractors or class 8 trucks.
 
Posts: 206 | Location: SE Michigan | Registered: June 15, 2010Reply With QuoteReport This Post
Vagabond Dreamer
Picture of Patrick-SP2022
posted Hide Post
I retired from the repair business over 20 years ago.
The Ingersoll Rand IR231 was the one I used for years. Never had a problem with it.



Yeah, well sometimes nothin' can be a real cool hand.
 
Posts: 3282 | Location: Texas | Registered: April 16, 2012Reply With QuoteReport This Post
Member
Picture of mark60
posted Hide Post
Add one more vote for an IR231
 
Posts: 2031 | Location: God Awful New York | Registered: July 01, 2006Reply With QuoteReport This Post
Member
posted Hide Post
Thanks all. Think the Aircat checks all the boxes.

Suggestions for sockets? Metric and SAE.


P229
 
Posts: 2871 | Location: Sacramento, CA | Registered: November 21, 2008Reply With QuoteReport This Post
Member
Picture of bushpilot
posted Hide Post
I have both air and electric (120 vac) and like the electric for power and ease of use. Most of my work is on aircraft and a '77 FJ40 I am restoring.


****************************************************W5SCM
"We the people are the rightful masters of both Congress and the courts, not to overthrow the Constitution but to overthrow the men who pervert the Constitution" - Abraham Lincoln

"I have been driven many times upon my knees by the overwhelming conviction that I had nowhere else to go" - Abraham Lincoln
 
Posts: 1081 | Location: Little Rock, AR | Registered: January 22, 2003Reply With QuoteReport This Post
Member
posted Hide Post
One name: Ingersoll Rand
 
Posts: 1901 | Location: Escaped Upstate NY for Texas | Registered: April 08, 2012Reply With QuoteReport This Post
Member
Picture of Beancooker
posted Hide Post
quote:
Originally posted by Russ59:
Thanks all. Think the Aircat checks all the boxes.

Suggestions for sockets? Metric and SAE.


6/8 recommend the Ingersol Rand, and you choose differently?
Why did you even ask us?




quote:
Originally posted by Balzé Halzé:
Before I figured you were just confused, but now I see that you're about as bright as a black hole, and twice as dense. Good lord.

The “lol” thread
 
Posts: 1262 | Location: Staring down at you with disdain, from the spooky mountaintop castle.  | Registered: November 20, 2010Reply With QuoteReport This Post
Woke up today..
Great day!
posted Hide Post
Been using IR impact tools for 20 years. Great power, completely rebuild-able, quality product. Top tier impact manufacturer IMO. Of course I am also now an IR Industrial Distributor Smile The automotive stuff is great for a home garage, the industrial impacts are great for high duty cycle use.
 
Posts: 1162 | Location: Chicagoland | Registered: December 10, 2008Reply With QuoteReport This Post
Member
posted Hide Post
For Air Tools IMO Ingersol Rand is much better for quality and service life than Chicago Pneumatic.

However I'm moving away from air, that darned hose has always been a hassle to deal with. What I am going to is Milwaukee M12 and M18 tools. Currently have two drill driver sets, one for work and one for home. Also have the Handisaw, a leaf blower, and am waiting on an extended 3/8 inch M12 ratchet to get to my store. Next up will be a 1/2 inch impact and Milwaukee offers 3 levels of M18 impacts in 1/2 inch. Two are high torque models with something in the range of 800 ft.lbs. for loosening. My choice will be the "reduced torque" model because I don't foresee the need to break loose anything with more than 400 ft/lbs. and the reduced torque model has nearly 2 times the rpms of the higher torque version. In addition it's lighter. BTW, for those needing to bust some really high torque fittings Milwaukee offers up to 1 inch drive M18 impact drivers with something like 2000 ft.lbs. of torque.

Yeah, I know, you didn't want to spend Snap on money for a Impact Wrench. Once you start using electrics instead of air you'll come to understand why it can be a real blessing to not have that damned hose to contend with.


I've stopped counting.
 
Posts: 4367 | Location: Michigan | Registered: November 07, 2008Reply With QuoteReport This Post
Like a party
in your pants
Picture of armored
posted Hide Post
For very occasional use at home I would look no further than Harbor Freight air tools.
I recently bought a HF Bauer corded impact with about 1100# of break away torque on sale now for $69.
 
Posts: 3369 | Location: Chicago, IL, USA: | Registered: November 17, 2002Reply With QuoteReport This Post
Go Vols!
Picture of Oz_Shadow
posted Hide Post
Make sure you have larger ID hose and fittings. Makes a difference.
 
Posts: 15772 | Location: SE Michigan | Registered: February 10, 2007Reply With QuoteReport This Post
Dances With
Tornados
posted Hide Post
I’m going to recommend an electric impact for you.

You’re not a professional using an air powered impact every day.

A good electric 1/2” impact doesn’t require you to maintain an air compressor, lines, hoses, fittings, pressure regulator, and a water filter. That’s more money chasing the air impact tool. That’s fine, if that’s what you want to do.

Just plug the electric into 120V power and you’re doing what task needs to be done.

Battery powered impacts are quickly becoming more powerful. However, since you’re not a Pro Tech, you don’t need to wonder where the battery charger and spare battery are, because your battery is flat.

My credentials for this advice? Former Snap On Tools Dealer.

Good luck to you, there is no wrong answer for you, whether Air powered, battery powered, or 120 V corded tool. Any will do what you want and need. Get the one you want.

When you do get the tool, then consider a torque wrench, don’t overtorque the fasteners.
 
Posts: 8238 | Registered: October 26, 2009Reply With QuoteReport This Post
Member
Picture of BlackTalonJHP
posted Hide Post
I like Sunex or Tekton for impact sockets
The Tekton are CrV instead of the usual CrMo so they are a little cheaper.
 
Posts: 198 | Location: Texas | Registered: September 18, 2019Reply With QuoteReport This Post
Member
posted Hide Post
quote:
Originally posted by Beancooker:
quote:
Originally posted by Russ59:
Thanks all. Think the Aircat checks all the boxes.

Suggestions for sockets? Metric and SAE.


6/8 recommend the Ingersol Rand, and you choose differently?
Why did you even ask us?


The IR231 has a max torque rating of 650 and my current wrench is 400#. Im afraid that I need to aim for >800#. IR in that range are well over $300.


P229
 
Posts: 2871 | Location: Sacramento, CA | Registered: November 21, 2008Reply With QuoteReport This Post
H.O.F.I.S
posted Hide Post
There is no fastner on a car or pick up truck that a Ir231 won't remove.



"I'm sorry, did I break your concentration"?
 
Posts: 1311 | Location: Above water | Registered: September 16, 2009Reply With QuoteReport This Post
Member
posted Hide Post
quote:
Originally posted by armored:
For very occasional use at home I would look no further than Harbor Freight air tools.
I recently bought a HF Bauer corded impact with about 1100# of break away torque on sale now for $69.


I have one of those, ot is great
 
Posts: 137 | Registered: January 11, 2018Reply With QuoteReport This Post
  Powered by Social Strata Page 1 2  
 

SIGforum.com    Main Page  Hop To Forum Categories  The Lounge    Recommendations 1/2” air impact wrench for home mechanic

© SIGforum 2019