SIGforum.com    Main Page  Hop To Forum Categories  SIG Armorer    Proper 320 cleaning
Go
New
Find
Notify
Tools
Reply
  
Proper 320 cleaning Login/Join 
Member
posted
After 500 to 600 rounds through my new P320, I got to wondering about the best way to clean the fire control module. Any suggestions?
 
Posts: 131 | Registered: January 14, 2015Reply With QuoteReport This Post
Member
Picture of az4783054
posted Hide Post
I remove the FCU and spray it liberally with brake cleaner (non chlorinated). After it dries apply lube of choice.

This message has been edited. Last edited by: az4783054,


Beware of a man whose only pistol is a 1911, he's probably very good with it.
 
Posts: 11194 | Location: Somewhere north of a hot humid hell in the summer. | Registered: January 09, 2009Reply With QuoteReport This Post
Member
posted Hide Post
Thanks.
 
Posts: 131 | Registered: January 14, 2015Reply With QuoteReport This Post
NOT compromised!
Picture of SIGWALLY
posted Hide Post
Best option is "Hornaday One Shot" gun cleaner and dry lube. This is in a black spray can. ( The red can is One Shot case lube) The spray cleans and flushes the firing system and when it dries it leaves behind a great dry lube. This is the best system of cleaning when you can not completely disassemble. Also great if you own a Remington Nylon 66. If you own one you know what I mean. Smile
 
Posts: 1527 | Location: Tampa Bay, Florida | Registered: July 06, 2003Reply With QuoteReport This Post
Member
posted Hide Post
^^^ Sounds interesting. Simple and easy...my favorite combo. Smile Think I'll give it a try.

I occasionally detail strip my classic P-series and 1911's for a thorough cleaning. No problem Have no interest in pulling apart the P320 FCU with it's springs and small parts for cleaning.


______________________
An expert is one who knows more and more about less and less until he knows absolutely everything about nothing. --Nicholas Murray Butler
 
Posts: 4670 | Location: Pennsylvania | Registered: June 29, 2006Reply With QuoteReport This Post
When you fall, I will be there to catch you -With love, the floor
posted Hide Post
Just spray it with brake cleaner. I use Slip2000 EWL. Lightly coat the rails and bearing surfaced. NONE in the striker assembly.

Frankly, I only clean mine every few thousand.


Richard Scalzo
Epping, NH

http://www.bigeastakitarescue.net
 
Posts: 5803 | Location: Epping, NH | Registered: October 16, 2004Reply With QuoteReport This Post
Member
posted Hide Post
Question for you brake cleaner guys. Since it's not specifically designed for firearms use, any risk of damage to the FCU components?

Thanks.


______________________
An expert is one who knows more and more about less and less until he knows absolutely everything about nothing. --Nicholas Murray Butler
 
Posts: 4670 | Location: Pennsylvania | Registered: June 29, 2006Reply With QuoteReport This Post
Freethinker
Picture of sigfreund
posted Hide Post
The slide catch lever post is, IIRC, made of plastic.
Although it’s in the slide, the striker assembly has a couple of plastic parts as well.




6.4/93.6

“Wise men talk because they have something to say; fools, because they have to say something.”
— Plato
 
Posts: 47365 | Location: 10,150 Feet Above Sea Level in Colorado | Registered: April 04, 2002Reply With QuoteReport This Post
Fighting the good fight
Picture of RogueJSK
posted Hide Post
quote:
Originally posted by Nipper:
Question for you brake cleaner guys. Since it's not specifically designed for firearms use, any risk of damage to the FCU components?

Thanks.


Markedly similar solvent compounds to non-chlorinated brake cleaner are sold as firearm cleaners under several different brands, such as "Birchwood Casey Gun Scrubber" and "Breakfree Powder Blast".

It's just cheaper to buy the generic non-chlorinated brake cleaner from the auto parts store than to buy the name brand stuff from the sporting goods store at a markup.

These products will not harm metal components. They're great for quickly cleaning and degreasing barrels, metal frames, slides, etc., and work well at removing cosmoline from metal parts. But they should be kept away from paint, wood, rubber, and plastic. They'll strip paint and wood finishes, and can break down rubber and some plastics.

Therefore, if any components of the FCU are plastic, I'd advise against simply hosing the FCU down with one of those solvent sprays. (I believe sigfruend is correct; the post that holds that spring on the underside of the slide lock lever is plastic. There may be other components too.)

Also note that metal that's been cleaned with these products will be completely dry and oil-free afterwards, so you'll need to be sure to fully oil/lube all the metal surfaces after cleaning.
 
Posts: 32428 | Location: Northwest Arkansas | Registered: January 06, 2008Reply With QuoteReport This Post
Member
posted Hide Post
Thanks for the tutorial on brake cleaners. Apparently, the devil is in the plastic details.

I guess I'm a closet brake cleaner user. I've used Birchwood Casey Gun Scrubber on traditional metal internal parts on my Classic Sigs, 1911's and revolvers.


______________________
An expert is one who knows more and more about less and less until he knows absolutely everything about nothing. --Nicholas Murray Butler
 
Posts: 4670 | Location: Pennsylvania | Registered: June 29, 2006Reply With QuoteReport This Post
When you fall, I will be there to catch you -With love, the floor
posted Hide Post
quote:
There may be other components too.)


Don't believe so. But I've used it for years and it didn't degrade any plastic parts. It will destroy paint or poly.


Richard Scalzo
Epping, NH

http://www.bigeastakitarescue.net
 
Posts: 5803 | Location: Epping, NH | Registered: October 16, 2004Reply With QuoteReport This Post
Member
Picture of 10-7 leo
posted Hide Post
Be cautious of the older online videos on stripping the 320. I have a 320 that was made a few months ago and there is one difference that I noticed.

Forgive my lack of proper nomenclature, I'm used to the classic P-series. There is a smaller diameter pin, that the video I watched showed, being removed from the right side of the FCG. The left side of this pin is under the safety lever bar?

In my newer 320, this pin still protrudes from the right side, and looks the same as the pin in the video, but it isn't. It has a slight head to it and is flush with the left side of the FCU. You can't tell by just looking at it, but it has to be removed from the left.

In order to remove it, you must remove the safety lever bar? first.



Sic Semper Tyrannis
If you beat your swords into plowshares, you will become farmers for those who didn't!
Political Correctness is fascism pretending to be Manners-George Carlin
 
Posts: 2038 | Location: Central FL | Registered: September 03, 2008Reply With QuoteReport This Post
Member
posted Hide Post
Thanks all for the advice
 
Posts: 131 | Registered: January 14, 2015Reply With QuoteReport This Post
Member
posted Hide Post
I spoke with a Sig armorer from NH at the P320 display at the IWA show this past March about this specific topic. I told him I was using non-chlorinated brake cleaner and/or carb cleaner to spray-out the FCUs on my P320 pistols, following-up with Rem-oil aerosol, and asked if this practice would damage the components. He cautioned against the use of the automotive solvents, noting that, at the very least, I was removing all lube from the internal contact surfaces and run the risk of not being able to sufficiently re-apply lube after the cleaning process. It was also noted that certain automotive solvents may be harmful to some materials as well.

Rather, he advised that I use a firearms-specific cleaner, and low-pressure compressed air, if I felt it necessary. I'm guessing that a can of compressed air, such as is used as a keyboard cleaner, may work for this.

He then suggested that I try TW-25, which is easy to apply in aerosol form, or any other quality grease lube. I now use TW-25 aerosol, and it works great for this application, and is easy to apply as well. One word of caution, it does have an odor to it, so I use it in a well-ventilated area.

Both of my P320 9mm FS now have Gray Guns triggers, which I originally installed with their furnished Lucas grease product. But, for periodic cleaning and maintenance, the TW-25 works great.

YMMV, but that's what works for me.
 
Posts: 312 | Location: Ohio | Registered: January 04, 2015Reply With QuoteReport This Post
Stupid
Allergy
Picture of dry-fly
posted Hide Post
Just a side note...re-assembling the FCU is a bitch. Be reasonably careful with it. Mine basically fell apart while trying to install the Gray Guns trigger (my fault).


"Attack life, it's going to kill you anyway." Steve McQueen...
 
Posts: 6996 | Location: TEXAS | Registered: July 18, 2005Reply With QuoteReport This Post
Member
posted Hide Post
Thanks to all for your replies and advice.
 
Posts: 131 | Registered: January 14, 2015Reply With QuoteReport This Post
Vote the
BASTIDS OUT!
Picture of yanici
posted Hide Post
quote:
Originally posted by Merc50:
I spoke with a Sig armorer from NH at the P320 display at the IWA show this past March about this specific topic. I told him I was using non-chlorinated brake cleaner and/or carb cleaner to spray-out the FCUs on my P320 pistols, following-up with Rem-oil aerosol, and asked if this practice would damage the components. He cautioned against the use of the automotive solvents, noting that, at the very least, I was removing all lube from the internal contact surfaces and run the risk of not being able to sufficiently re-apply lube after the cleaning process. It was also noted that certain automotive solvents may be harmful to some materials as well.

Rather, he advised that I use a firearms-specific cleaner, and low-pressure compressed air, if I felt it necessary. I'm guessing that a can of compressed air, such as is used as a keyboard cleaner, may work for this.

He then suggested that I try TW-25, which is easy to apply in aerosol form, or any other quality grease lube. I now use TW-25 aerosol, and it works great for this application, and is easy to apply as well. One word of caution, it does have an odor to it, so I use it in a well-ventilated area.

Both of my P320 9mm FS now have Gray Guns triggers, which I originally installed with their furnished Lucas grease product. But, for periodic cleaning and maintenance, the TW-25 works great.

YMMV, but that's what works for me.


I've read reviews that the spray bottle treatment gummed up after a while. I haven't used it but I don't think I'd take the chance.


John

"Building a wall will violate the rights of millions of illegals." [Nancy Pelosi]
 
Posts: 2401 | Location: N.E. Massachusetts | Registered: June 05, 2009Reply With QuoteReport This Post
You're going to feel
a little pressure...
posted Hide Post
I think Eezox in the aerosol spray bottle would do the job rather nicely.
Smells good, too.

Bruce






"The designer of the gun had clearly not been instructed to beat about the bush. 'Make it evil,' he'd been told. 'Make it totally clear that this gun has a right end and a wrong end. Make it totally clear to anyone standing at the wrong end that things are going badly for them. If that means sticking all sort of spikes and prongs and blackened bits all over it then so be it. This is not a gun for hanging over the fireplace or sticking in the umbrella stand, it is a gun for going out and making people miserable with." -Douglas Adams

“It is just as difficult and dangerous to try to free a people that wants to remain servile as it is to try to enslave a people that wants to remain free."
-Niccolo Machiavelli

The trouble with fighting for human freedom is that one spends most of one's time defending scoundrels. For it is against scoundrels that oppressive laws are first aimed, and oppression must be stopped at the beginning if it is to be stopped at all. -Mencken
 
Posts: 4245 | Location: AK-49 | Registered: October 06, 2011Reply With QuoteReport This Post
You're going to feel
a little pressure...
posted Hide Post
So, I just cleaned, for the first time, a used P320 I bought.
It had a bunch of grease on the striker assembly and in the striker channel.
Is that normal and recommended?
I'm accustomed to Glocks where that is a big no-no.

Bruce






"The designer of the gun had clearly not been instructed to beat about the bush. 'Make it evil,' he'd been told. 'Make it totally clear that this gun has a right end and a wrong end. Make it totally clear to anyone standing at the wrong end that things are going badly for them. If that means sticking all sort of spikes and prongs and blackened bits all over it then so be it. This is not a gun for hanging over the fireplace or sticking in the umbrella stand, it is a gun for going out and making people miserable with." -Douglas Adams

“It is just as difficult and dangerous to try to free a people that wants to remain servile as it is to try to enslave a people that wants to remain free."
-Niccolo Machiavelli

The trouble with fighting for human freedom is that one spends most of one's time defending scoundrels. For it is against scoundrels that oppressive laws are first aimed, and oppression must be stopped at the beginning if it is to be stopped at all. -Mencken
 
Posts: 4245 | Location: AK-49 | Registered: October 06, 2011Reply With QuoteReport This Post
Member
Picture of 10-7 leo
posted Hide Post
There should not be any significant lube in the striker channel. It will only collect dirt and cause problems.

I run a wet q-tip in the channel, followed by one or two dry ones, leaving a slight oil film. Light film on the striker parts, also.



Sic Semper Tyrannis
If you beat your swords into plowshares, you will become farmers for those who didn't!
Political Correctness is fascism pretending to be Manners-George Carlin
 
Posts: 2038 | Location: Central FL | Registered: September 03, 2008Reply With QuoteReport This Post
  Powered by Social Strata  
 

SIGforum.com    Main Page  Hop To Forum Categories  SIG Armorer    Proper 320 cleaning

© SIGforum 2024